Abstract:Cold-drawn pearlitic steel wires exhibit ultrahigh strength and have important applications where high strength and wear resistance are required. The hypereutectoid compositions present a promising potential for increasing the mechanical properties, especially the strength. The austenitization process strongly influences the following pearlitic microstructure and thus the mechanical properties. Continuous heating is always used in the industrial processing. However, the austenitization of pearlite in hypereutectoid steels during continuous heating has not been investigated systematically. In this work, the dilatometer and DSC were employed to investigate the austenitization kinetics of hypereutectoid steels during continuous heating. Microstructure evolution was observed with SEM and EBSD. The dilatometer and DSC curves were analyzed with derivative method. The whole austenitization can be divided into five stages: initial microstructure, reverse eutectoid transformation, retained cementite dissolution, homogenization and homogeneous austenite. Tangent method was used for measuring the critical temperatures of different stages. Experimental determination of transformed fraction was obtained through the lever method. Calculation with Thermo-Calc and Dictra software was carried out for the austenitization and considered to be a reasonable result by comparing with the experimental data. There is a turning point for the reduction rate of cementite and formation of austenite at the finishing temperature of reverse eutectoid transformation, which is similar with the austenitization in low carbon steel and spheroidal pearlite of hypereutectoid steel. Effects of heating rates, initial microstructure and carbon content were studied by varying the relevant parameters. Higher heating rate in- creases the starting and finishing temperatures of reverse eutectoid transformation and widens the temperature range, has no effect on the finishing temperature of retained cementite dissolution, increases the finishing temperature of homogenization. Coarser initial pearlitic microstructure increases the starting and finishing temperatures, widens the temperature range for reverse eutectoid transformation, increases the finishing temperature for retained cementite dissolution and homogenization. Enhancement of carbon content has little effect on the reverse eutectoid transformation, but increases the finishing temperature for retained cementite dissolution and homogenization. The effects mentioned above on the austenitization kinetics were discussed for mechanism analysis and compared with the observations of relevant systems provided by other research.

Short time austenitizing effects on the hardenability of 0.55 wt. pct. Carbon steels

Microstructure and Notched Fracture Resistance of Low Alloy 0.56% C Steels after Simulated Induction Hardening

Insight into the induction hardening behavior of a new 0.40% C microalloyed steel: Effects of initial microstructure and thermal cycles

Aspects of Austenitization for the Bearing Steel Induction Quenching Design

Effect of Rapid Heating and Quenching on Microstructure and Mechanical Properties of High Strength Low Alloy Steel

Atom-probe tomographic and dilatometric studies of phase-transformations after inter-critical annealing of a low-carbon dual-phase steel

Strengthening and Toughening Mechanisms in Martensitic Steel

Increasing the Strength and Impact Toughness of Carbon Steel Using a Nanosized Eutectoid Resulting from Time-Controlled Quenching

Investigation of Austenitization During Continuous Heating Process in Hypereutectoid Steels

Effects of Different Austenitizing Times on the Microstructure and Properties of Cr‐Ni‐Mo‐V Series High‐Strength Steels

Effects of Austenitizing Conditions on the Microstructure of AISI M42 High-Speed Steel

The effect of austenitizing temperature on the microstructure and mechanical properties of as-quenched 4340 steel

The Transformation of Carbides during Austenization and Its Effect on the Wear Resistance of High Speed Steel Rolls

A quantitative study of the formation of austenite and the solution of cementite at different austenitizing temperatures for a 1.27% carbon steel

Austenitizing Temperature and Cooling Rate Effects on the Martensitic Transformation in a Microalloyed-Steel

Early Martensitic Transformation in a 0.74C–1.15Mn–1.08Cr High Carbon Steel

Austenite Decomposition of a Lean Medium Mn Steel Suitable for Quenching and Partitioning Process: Comparison of CCT and DCCT Diagram and Their Microstructural Changes

Enhancing Ductility of Martensitic Steels Through Cryogenic Treatment

A Dilatometric Study of Austenite Transformation in Aircraft Steel During Quenching–Partitioning and Austempering

Effect of Spheroidizing Annealing Process on Microstructure and Properties of Quenching and Tempering 60Cr16MoMA Martensitic Stainless Steel

The Effect of Long-Time Austenization on the Wear Resistance and Thermal Fatigue Properties of a High-Speed Steel Roll