Abstract:The detection of impact damage in fibre reinforced composites is of significant concern because such damage can reduce the load-bearing ability of the composite. A number of factors can influence the nature and extent of impact damage development in composites including: (a) the type of reinforcing fibre and resin system; (b) the magnitude of the residual (fabrication) stresses; (c) the lay-up sequence; and (d) other factors such as the nature of the impactor, impact velocity, impact energy, temperature, moisture content in the composites, etc. From a structural health monitoring point of view, it is necessary to investigate the distribution of damage through the thickness of the composite.This paper reports on a simple, partially multiplexed optical fibre strain sensor system for in-situ strain and residual strain measurements in a carbon fibre reinforced epoxy composite. An extrinsic Fabry-Perot interferometric (EFPI) sensor design was used along with single-mode fibres. The multiplexing scheme was based on wavelength division via the use of two super luminescent diodes (SLDs) at different wavelengths. A low-cost fibre optic CCD spectrometer was used as the detector. The multiplexing scheme was demonstrated using two EFPI sensors. In principle, a number of EFPI sensors can be multiplexed using the proposed scheme provided that each sensor is illuminated at a specified and different wavelength.The feasibility of detecting the residual strain in the composite was demonstrated successfully at two specified positions within a 16-ply carbon fibre reinforced composite panel. Preliminary results indicated that the sensor system was also capable of detecting the effects of a 3.2 J impact. Excellent correlation was obtained between the EFPI sensor output and that obtained using surface mounted strain gauges.

A Novel Extrinsic Fabry-Perot Interferometric Sensor for Inconel 718 Tensile Properties Measurement

Research on Full Strain Measurement Performance of Non-intrinsic Optical Fiber F-P Sensor

Large-Scale Strain Measurement of Micro-Specimens in High-Temperature Environments Based on Efpi

An Extrinsic Fabry–Perot Interferometer-Based Large Strain Sensor with High Resolution

Probing Nanostrain Via a Mechanically Designed Optical Fiber Interferometer

Optical Fiber Sensor for Tensile and Compressive Strain Measurements by White-Light Fabry–Perot Interferometry

Optical Fiber Sensor and Assembly Method for Measuring the Tensile Strain of a Nickel-Based Directionally Solidified Superalloy in a High-Temperature Environment.

An embeddable optical strain gauge based on a buckled beam

Experimental Research of Strain and Temperature Based on Efpi Sensor

High-Sensitivity Fiber Fabry-Pérot Interferometer Strain Sensor

Extrinsic Fabry-Perot Sensor for Strain and Crack Opening Displacement Measurements from -200 to 900 Degrees C

Optical fiber Fabry-Perot interferometer based embeddable strain sensor with 30 nano-strain resolution

Simultaneous Strain and Temperature Measurements in Composites Using Extrinsic Fabry–Perot Interferometric and Intrinsic Rare-Earth Doped Fiber Sensors

Miniature Optical Fiber Strain Sensor Based on Fabry-Perot Interferometer

High-sensitivity Strain Sensor Based on In-Fiber Improved Fabry-Perot Interferometer.

Fiber-optic extrinsic Fabry-Perot interferometer strain sensor with <50 pm displacement resolution using three-wavelength digital phase demodulation.

Simultaneous Strain and Temperature Measurement Using an Integrated Fibre Bragg Grating Extrinsic Fabry-Perot Sensor

A Multiplexed Extrinsic Fabry-Perot Sensor System for In-Situ Strain and Impact Damage Detection in Composites

Hyperelastic Polymer Fiber Fabry–Pérot Interferometer for Nanoforce Measurement

A Miniature Extrinsic Fabry-Pérot Interferometer Strain Sensor Based on Hollow-Core Photonic Crystal Fiber

A Multiplexed Optical Fibre-Based Extrinsic Fabry-Perot Sensor System Forin-Situstrain Monitoring in Composites