Abstract:Magnesium‐lithium (MgLi) alloys have been widely used in various engineering fields due to their ultra-light characteristics. The strengthening of MgLi alloys is one of the key factors determining its application and has received extensive attention. In this work, the as-cast ultralight and high strength Mg-10Li-3Al-3Zn-xY (x = 0, 0.5 and 1.0, wt%) alloys with a density of only 1.52 g/cm3 were prepared via vacuum induction melting. The effects of rare earth element yttrium (Y) on the microstructure and mechanical properties of the MgLi alloy system were investigated. The results indicated that the microstructures of all the alloys mainly consisted of α-Mg, β-Li, AlLi, and MgLi2Al phases. The spherical AlLi phase was distributed inside the α-Mg and β-Li matrix. Part of the petal-like MgLi2Al phase was distributed in the interior of β-Li, and the rest grew along the grain boundaries as long strips. With the addition of Y, Al2Y phase formed with sharp edges and regular shapes. The Al2Y phase was mainly distributed inside the α-Mg phase and along the grain boundaries. Meanwhile, the amount of AlLi phase inside the α-Mg phase gradually decreased. The presence of nano-scale lath-shape MgLiZn phase in the β-Li matrix was observed in the HAADF map of the 0.5Y alloy. The continuous growth of MgLi2Al phase at the grain boundaries weakened its strength. As a consequence, it eventually led to intergranular fracture of the alloy. The 0.5Y alloy showed the highest tensile strength, up to ~244 MPa, and the yield strength was 60.5% higher than that of the 0Y alloy. Solid solution strengthening, precipitate strengthening and grain refinement were thus considered as the primary strengthening mechanisms caused by the addition of Y into the Mg-10Li-3Al-3Zn alloy.

Microstructure and Mechanical Properties of As-Cast and Solid Solution Treated Mg−8Li−xAl−yZn Alloys

Effect of Zn Concentration on the Microstructure and Mechanical Properties of Al-Mg-Si-Zn Alloys Processed by Gravity Die Casting

The Microstructure and Mechanical Properties of As-cast Mg-10Gd-3Y-xZn-0.6Zr (x=0, 0.5, 1 and 2 Wt%) Alloys

Effect of Al on Microstructure and Mechanical Properties of Mg-10Li-3Zn-1Y Alloys

Microstructure and mechanical properties of as-cast Mg−8Li−xZn−yGd (x=1, 2, 3, 4; y=1, 2) alloys

Microstructure and mechanical properties of as-cast ultralight and high strength Mg-10Li-3Al-3Zn-xY alloy with multi-precipitates

Microstructures and Mechanical Properties of Ultralight Cast Al-3Li-XMg-0.1Zr Alloys

Influence of Heat Treatment on Microstructure and Mechanical Properties of As-Cast Mg–8Li–3Al–2Zn–xY Alloy with Duplex Structure

Microstructural Characteristics and Mechanical Properties of Extruded Al-4Cu-1Li-0.4Mg-0.1Zr-xZn Alloy

Balance of Mechanical Properties of Mg-8Li-3Al-2Zn-0.5Y Alloy by Solution and Low-Temperature Aging Treatment

High-cycle Fatigue Behavior of Mg-8Li-3Al-2Zn-0.5Y Alloy under Different States

Microstructure And Mechanical Properties Of Mg-8li-4al-0.3y Alloys

Microstructure and Mechanical Properties of Mg, Ag and Zn Multi-Microalloyed Al–(3.2–3.8)Cu–(1.0–1.4)Li Alloys

Effects of Zn/Al Mass Ratio on Microstructure Evolution and Mechanical Properties of Mg–Sn Based Alloys

Effect of Zn Addition on the Microstructure and Mechanical Properties of As-Cast BCC Mg-11Li Based Alloys

Microstructure and Mechanical Properties of Mg–6Li–xAl–0.8Sn Alloys

Effect of Composition on the Microstructure and Mechanical Properties of Mg–Zn–Al Alloys

Effects of Li Content on Microstructure and Mechanical Properties of As-Cast Mg?xLi?3Al?2Zn?0.5Y Alloys

Effects of Al and Zn Contents on the Microstructure and Mechanical Properties of Mg-Al-Zn-Ca Magnesium Alloys

Variation in the Microstructure and Mechanical Properties of Permanent Mold Cast Al–3Li–2Mg–0.1Zr Alloy with Zn Addition

Effect of composition on the microstructure and mechanical properties of Mg-Al-Zn alloys