Abstract:The impact of minor Mg addition on microstructure and mechanical properties of cast Al–Li–Cu–Zr alloy with high lithium content (3 wt % Li) were studied to understand a qualitative assessment of sequence and kinetics of multiple precipitations and its effect on mechanical properties. Scanning Electron Microscope and X-ray diffraction results suggested that raising the content of Mg gradually altered the grain structure of the as-cast alloys and increased the types and volume fraction of the grain boundary intermetallic phase. Unusually, solvus temperature is higher than solidus temperature in 0.5 Mg alloy (Al–3Li–2Cu-0.5Mg-0.15Zr, wt. %), resulting in the incipient melting of the matrix before the complete dissolution of the intermetallic phases. Prominent enhancements in both age-hardening and precipitation kinetics of the base alloy with the addition of Mg were also easily identified, indicating the important role of Mg during isothermal aging. Transmission Electron Microscope and atom probe tomography results showed that minor Mg addition (0.2 wt %, denoted by 0.2 Mg alloy) could encourage the diffusion of Cu atoms by the aggregation of Mg–Cu-vacancy co-clusters, thereby promoting the nucleation of the T1-Al2CuLi and θ′-Al2Cu precipitates. In addition, S′-Al2CuMg precipitate was therefore introduced as a result of Mg addition. With further increasing the content of Mg to 0.5 wt %, the nucleation and growth of S′ precipitate would be promoted at the expense of T1 and θ′ precipitates, especially the latter. Based on the theoretical models and regression analysis, the formation mechanism of δ′-Al3Li precipitate-free-zones gradually changed from the initial vacancy-depletion mechanism to the solute-depletion mechanism, and Mg element could significantly inhibit the coarsening of δ′ precipitate-free-zones. The best balance between ductility and strength was obtained by 0.2 Mg alloy aged for 32 h, and the alloys have significant advantages in terms of density (2.437 g/cm3) and elastic modulus (82.65 GPa) over conventional cast aluminum alloys (density: 2.7–2.8 g/cm3; elastic modulus: 72 GPa).

Variation in the Microstructure and Mechanical Properties of Permanent Mold Cast Al–3Li–2Mg–0.1Zr Alloy with Zn Addition

The Microstructure and Mechanical Properties of As-cast Mg-10Gd-3Y-xZn-0.6Zr (x=0, 0.5, 1 and 2 Wt%) Alloys

Microstructure and Mechanical Properties of As-Cast Al-10Ce-3Mg-xZn Alloys

Significant roles of minor Mg addition in microstructural evolution and mechanical properties of cast Al–3Li–2Cu-0.15Zr alloy

Effect of Ti Addition on the Microstructure and Mechanical Properties of Cast Mg-Gd-Y-Zn Alloys

Microstructure, Mechanical Properties and Corrosion Behaviors of Al–Li–Cu–Mg–Ag–Zn Alloys

Influence of Zr content on microstructure and mechanical properties of As-cast Al-Zn-Mg-Cu alloy

Effect of Zn/Mg ratio on microstructure and mechanical properties of Al-Zn-Mg alloys

Effect of Zr addition on the microstructure evolution and mechanical properties of extruded Al-Cu-Li-Mn alloys

Effect of Zn Concentration on the Microstructures and Mechanical Properties of Extruded Mg–7Y–4Gd–0.4Zr Alloys

Influence of Zn on the microstructure and mechanical properties of Mg-Gd-Zr alloy

Influence of Al Addition on the Microstructure and Mechanical Properties of Mg-Zn-Sn-Mn-Ca Alloys

The development of low-temperature heat-treatable high-pressure die-cast Al–Mg–Fe–Mn alloys with Zn

Effects of Mg content on microstructure and mechanical properties of low Zn-containing Al−xMg−3Zn−1Cu cast alloys

Effect of Zn/Mg ratio on T6 state microstructure and properties of Al-xZn-2.6Mg-0.94Cu-0.2Zr-0.8Ti cold extruded aluminum alloy

Effect of Zn/Mg Ratio on Microstructure and Properties of Cold Extruded Al-xZn-2.4Mg-0.84Cu-0.2Zr-0.25Ti Aluminum Alloy

Influence of large amount Zn on mechanical properties and corrosion resistance of 5083 hot rolled aluminum alloy

The influence of Zn addition on the microstructure and mechanical and corrosion properties of warm rolled Al mg alloys containing Er and Zr

Effect of Al addition on microstructure and mechanical properties of Mg−Gd−Zn alloys

Effect of Al on Microstructure and Mechanical Properties of Mg-10Li-3Zn-1Y Alloys

Influence of Zr Microalloying on the Microstructure and Room-/High-Temperature Mechanical Properties of an Al–Cu–Mn–Fe Alloy