Abstract:Due to the uncertain fracture of the die-casting aluminum component (shock tower), X-ray tomography (XRT) coupled with digital image correlation (DIC) was implemented to understand various pore characteristics, specifically spatial distribution and morphology of porosity, and their influences on the ductility in thin-walled Al-10Si-0.3 Mg high pressure die casting. XRT analysis reveals that there was a great amount of porosity in the samples, which was heterogeneously distributed. DIC measurement indicates that porosity gave rise to strain concentration and reduced ductility. Finite element simulations were performed to reveal the combined effect of the pore size and location. Though the morphology and location of pore had nonnegligible impacts on ductility, the local porosity in fracture region played a dominant role in determining it. The local porosity in fracture region can't be obtained prior to tensile testing and consequently ductility can't be predicted based on it. It was found that, for the 27 studied samples, the local porosities in fracture regions were equal or close to the highest local porosities in the gauges, and the samples with higher level of the highest local porosity generally showed lower elongations. The range in which the ductility falls could be estimated according to the highest local porosity in the gauge, which can be achieved before tensile testing. The factors accounting for the difference between upper and lower bounds on ductility were also discussed.(c) 2023 The Authors. Published by Elsevier B.V. This is an open access article under the CC BY-NC-ND license (http://creativecommons.org/licenses/by-nc-nd/4.0/).

The Ductility Variation of High-Pressure Die-Cast AE44 Alloy: the Role of Inhomogeneous Microstructure

Quantitative Analysis of 3D Pore Characteristics Effect on the Ductility of HPDC Al-10Si-0.3Mg Alloy through X-Ray Tomography

Quantitative Analysis of 3D Pore Characteristics Effect on the Ductility of HPDC Al–10Si-0.3 Mg Alloy Through X-ray Tomography

Influences of Initial Porosity, Stress Triaxiality and Lode Parameter on Plastic Deformation and Ductile Fracture

Formation Mechanism of the Microstructural Heterogeneity in a Die-Cast Al-Mg-Si Alloy and Its Effect on Mechanical Properties

Effect of as-cast microstructure heterogeneity on aging behavior of a high-pressure die-cast A380 alloy

Achieving Superior Ductility with Ultrahigh Strength Via Deformation and Strain Hardening in the Non-Recrystallized Regions of the Heterogeneous-Structured High-Entropy Alloy

Heterogeneous Microstructure and Deformation Behavior of an Automotive Grade Aluminum Alloy

Micromechanical origin for the wide range of strength-ductility trade-off in metastable high entropy alloys†

Macro-heterogeneities in microstructures, concentrations, defects and tensile properties of die cast Al–Mg–Si alloys

Microstructural origins of high strength and high ductility in an AlCoCrFeNi2.1 eutectic high-entropy alloy

Extra Strain Hardening in High Pressure Die Casting Mg-Al-RE Alloy

The Correlation Between Microstructure and Mechanical Properties of High-Pressure Die-Cast AM50 Alloy

Effects of Shot Sleeve Pre-solidification on the Microstructure and Tensile Properties of High Pressure Die Cast AE44

In-situ investigation of damage mechanisms in duplex AlCoCrFeNi2.1 high entropy alloy

The effect of different high pressure die casting parameters on 3D microstructure and mechanical properties of AE44 magnesium alloy

Discontinuous Coarsening Leads to Unchanged Tensile Properties in High-Entropy Alloys with Different Recrystallization Volume Fractions

Effect of compositional heterogeneity on the mechanical properties of a single-phase Cu-9Al alloy with different grain sizes

Influence of Multi-Microstructural Alterations on Tensile Property Inhomogeneity of 7055 Aluminum Alloy Medium Thick Plate

Ductility prediction of HPDC aluminum alloy using a probabilistic ductile fracture model

The Variation in Microstructure and Thermal Conductivity of a Plate-Like Al-Fe-Ni High-Pressure Die Casting