Abstract:Ti-2Al-2.5Zr alloy with hcp structure is a kind of structural materials used under low temperature condition, e.g. pipeline system of liquid hydrogen and liquid oxygen in missile engine. It is usually serviced in condition of severe low temperature and dynamic loading. Deformation twinning is a common and important plastic deformation mode in the hexagonal close-packed alloy., but will be severely restricted as the grain is refined from tens of microns to a few microns. On the other hand, twinning has a low sensitivity to temperature, consequently becomes a favorable deformation mode at low temperature in comparison with dislocation slip. The objective of this work is to study the coupling effect of grain refinement and testing temperature on twinning behavior and the low-cycle fatigue behavior of Ti-2Al-2.5Zr.Symmetrical push-pull low-cycle fatigue (LCF) tests were performed on Ti-2Al-2.5Zr with grain size of about 5 pm at room temperature (RT) and low temperature (77 K). The results show that the alloy exhibits the higher ductility and the longer low-cycle fatigue life at 77 K than those at RT. The cyclic stress response curves show that the cyclic softening occurs at the low strain amplitudes of 0.5% and 1.0%. However, as strain amplitude increased to 1.5% and 2.0%, cyclic stress saturation appeared. When testing temperature declined to 77 K, the cyclic hardening was observed at all four strain amplitudes. The degree of cyclic hardening increases as the strain amplitude rises. The fractography analyses suggest that transgranular fracture with well-developed fatigue striations is the predominant failure mode. The amount of secondary cracks is much higher in the alloys deformed at RT than that at 77 K. TEM examination reveals that deformation twins become more active. The primary types of twinning are {10 (1) over bar1} and {11 (2) over bar1}. The typical deformation microstructures consist of individual dislocation lines together with the tangled dislocation at the low strain amplitudes of 0.5% and 1.0%. As the strain amplitude increased to 1.5% and 2.0%, {10 (1) over bar0} prismatic slip and {11 (2) over bar1} pyramidal slip were simultaneously activated, the subgrain and dislocation cells were formed. At 77 K and strain amplitude of 2.0%, the parallel dislocation bands distribute along prismatic plane. As the strain amplitude increased to 4.5%, mutua l perpendicular dislocation lines appeared. The improvement of fatigue life of Ti-2Al-2.5Zr at 77 K is attributed to the constraint of inhomogeneous slip and the activation of deformation twinning.

Low-cycle Fatigue Behavior and Deformation Substructure of Ti-2Al-2.5Zr Alloy at 673K

Low-cycle fatigue behavior and deformation substructure of Ti-2Al-2.5Zr alloy at 673 K

Low-Cycle Fatigue Behavior and Deformation Substructure of Ti-2al-2.5zr Alloy at 298 and 673K

LOW CYCLE FATIGUE BEHAVIORS AND MICROSTRUCTURES OF Ti–2Al–2.5Zr WITH FINE GRAIN AT RT AND 77 K

A Study of the Back Stress and the Friction Stress Behaviors of Ti-6Al-4V Alloy During Low Cycle Fatigue at Room Temperature

Effect of Grain Size and Testing Temperature on Low-Cycle Fatigue Behavior and Plastic Deformation Mode of Ti-2Al-2.5Zr

Low cycle fatigue behavior of nickel-based superalloy GH4145/SQ at elevated temperature

High Temperature Low Cycle Fatigue Properties and Failure Mechanism of a TiAl Alloy

Microstructure evolution and cyclic deformation behavior of Ti-6Al-4 V alloy via electron beam melting during low cycle fatigue

Low Cycle Fatigue, Creep and Creep-Fatigue Interaction Behavior of a TiAl Alloy at High Temperatures

Effect of Dwell Condition on Fatigue Behavior of a High-Nb TiAl Alloy at 750 °C

Effect of Grain Size on Twinning Behavior in Ti–2Al–2.5Zr Alloy Fatigued at 77K

Low cycle fatigue properties and microscopic deformation structure of Zircaloy-4 in recrystallized and stress-relieved conditions

Isothermal and thermomechanical fatigue behavior of Ti-2Al-2.5Zr titanium alloy

Low-Cycle Fatigue Behavior and Fracture Characteristics of Low-Cost Ti-2Fe-0.1B Alloy

Deformation Mechanisms of Selective Laser Melted 316l Austenitic Stainless Steel in High Temperature Low Cycle Fatigue

Influence of Strain Amplitude on Low-Cycle Fatigue Behaviors of a Fourth-Generation Ni-Based Single-Crystal Superalloy at 980 °C

On the Microstructure Evolution During Low Cycle Fatigue Deformation of Wrought ATI 718plus Alloy

Microscopic Characterization on Low Cycle Fatigue Behavior at Room Temperature of Zircaloy-4 Alloy with Recrystallized Microstructure

Cyclic Deformation Behavior of a Nickel-Base Superalloy under Fatigue Loading

Microstructure stability and damage mechanisms in an α/β Ti-6Al-4V-0.55Fe alloy during low cycle dwell-fatigue at room temperature