Abstract:Low-cycle fatigue (LCF) behavior of nickel-based precipitation-strengthened superalloy GH4145/SQ was investigated systematically under fully reversed total strain amplitude control conditions at 538°C in laboratory air. It was shown that the alloy exhibited a pronounced initial fatigue hardening followed by continuous fatigue softening to failure at high strain amplitudes, while at low strain amplitudes the initial hardening was followed by a well-defined saturation stage. Microstructure observations using optical and transmission-electron microscopy revealed that slip band density increased with increasing total strain amplitudes and the size of the γ′precipitates tended to reduction due to repeated shearing by the dislocations with continuous cyclic straining. The above changes in microstructures during cycling were essentially responsible for the fatigue hardening–softening behavior of the alloy. Both optical and SEM micrographs indicated that at low strain amplitudes crack propagation was basically transgranular, while at high strain amplitudes crack propagation was essentially intergranular. Bilinear behavior with a change of slope at a plastic strain amplitude of about 0.2pct was observed in cyclic stress–strain (CSS), Coffin–Manson (C–M) and plastic strain energy–life plots. A change in the number of operating slip systems and the fracture modes with the strain amplitude employed was used to explain this two-slope characteristic. In both the companion specimens test (CST) and the incremental step test (IST) methods the alloy exhibited non-masing type behavior. It was suggested that, for the first approximation, the half-life plastic strain energy could be calculated directly according to the equation without reckoning in the non-masing behavior.

On the Microstructure Evolution During Low Cycle Fatigue Deformation of Wrought ATI 718plus Alloy

Low cycle fatigue behavior of nickel-based superalloy GH4145/SQ at elevated temperature

Strain Ratio Effects on Low-Cycle Fatigue Behavior and Deformation Microstructure of 2124-T851 Aluminum Alloy

Influence of Prior Low Cycle Fatigue on Microstructure Evolution and Subsequent Creep Behavior

Low-cycle Fatigue Behavior and Property of TA15 Titanium Alloy with Tri-Modal Microstructure

Deformation Mechanisms of Selective Laser Melted 316l Austenitic Stainless Steel in High Temperature Low Cycle Fatigue

Study on Low Fatigue Damage Behavior of TC17 Titanium Alloy with Basket-Weave Microstructure

Influence of Strain Amplitude on Low-Cycle Fatigue Behaviors of a Fourth-Generation Ni-Based Single-Crystal Superalloy at 980 °C

Low Cycle Fatigue Failure Analysis of a Ni‐Based Single Crystal Superalloys at 850 °C

Effect of Heat Treatment on Low Cycle Fatigue of In718 Superalloy at the Elevated Temperatures

The Influence of Dwell Time on Low Cycle Fatigue Behavior of Ni-Base Superalloy Ic10

Low Cycle Fatigue Behavior and Deformation Mechanism of Ti–6Al–4V-0.55Fe Alloy under the Control of Strain and Stress Amplitudes

Microstructure evolution and cyclic deformation behavior of Ti-6Al-4 V alloy via electron beam melting during low cycle fatigue

Influence of microstructure on strain controlled low cycle fatigue crack initiation and propagation of Ti-55531 alloy

Microstructure Evolution of Al–12Si–CuNiMg Alloy under High Temperature Low Cycle Fatigue

Correlation Between Microstructure Evolution and Mechanical Response in a Moderately Low Stacking-Fault-energy Austenitic Fe–Mn–Si–Al Alloy During Low-Cycle Fatigue Deformation

High Temperature Low-Cycle Fatigue, Deformation Microstructure and Final Fracture Behavior of a Nickel-Base Superalloy

In-situ SEM-EBSD investigation of the low-cycle fatigue deformation behavior of Inconel 718 at grain-scale

Low-cycle fatigue behavior and deformation substructure of Ti-2Al-2.5Zr alloy at 673 K

Microstructure evolution, failure mechanism and life prediction of additively manufactured Inconel 625 superalloy with comparable low cycle fatigue performance

Study On Low Cycle Fatigue Behavior Of Ti-3al-5mo-4cr-2zr-1fe Alloy With High Strength And Toughness