Abstract:Background: The Accelerator Driven Subcritical System (ADS) uses a proton beam incident on a target to produce neutrons used in a nuclear reactor to process spent fuel in two ways: to accelerate its decomposition into non-radioactive waste, and to increase the rate at which it is recycled into nuclear fuel. Two cryomodules, each consisting of 7 superconducting spoke cavities, 7 superconducting magnets and 7 beam position monitors, are used to accelerate the proton beams from 3.2 MeV to 10 MeV. The superconducting magnet contains a solenoid for beam focusing and two correctors for orbit correction, it is a key component for ADS injection. Purpose: This study aims at a short superconducting magnet design to meet the required integral field strength and to reduce the leakage field at the nearby superconducting spoke cavities. The design current for the solenoid is 210 A. Methods: The main solenoid and two bucking solenoids plus the iron yoke were used to meet the leakage field requirements which is less than 1 G at a distance of 270 mm from the solenoid center. In order to shorten the magnet length to 170 mm, special design methods were taken for the magnet cryostat by removing two conflicts flanges and replacing them with the direct Al ring seal methods. A kind of conducted the current leads similar as that of Large Hadron Collider (LHC) corrector magnets was applied to the 2.1-K, 3 100-Pa cryogenic system. The small store energy magnet led to the introduction of active quench detected system, which is much more reliable. Two short magnets and two spoke cavities were installed inside a test cryomodule to test the online operation properties of the SC magnet and the SC spoke cavity. Results: A quench performance in the vertical test shows that the operating current of the solenoid magnet can reach above 300 A after natural quenching on three occasions during current ramping (260 A, 268 A and 308 A). Online operating test shows that two magnets can work at 4.2 K and 2.1 K, respectively. The quench protection system worked well when two quenches occurred as the liquid helium level decreased. Conclusion: The online operation for the two magnets confirms the physical and the mechanical design, the reliability of the quench detection technique.

Design and Test of an 8T Focusing Superconducting Solenoid of FRIB Driver Linac

Cryogenic Test of the FRIB Superconducting Magnets at IMP

Design and testing of focusing magnets for a compact electron linac

Mechanical Design of the Half-length Prototype for a Superconducting FECR Ion Source

Superconducting Magnet Development for the HIAF Accelerator Complex

Tests on a 6 T Conduction-Cooled Superconducting Magnet

Design of a Superconducting Gantry Dipole Magnet Based on Tilted Solenoids

HIGH INTENSITY NEUTRINO SOURCE SUPERCONDUCTING SOLENOID CRYOSTAT DESIGN

Design, Development and Fabrication for BESIII Superconducting Muon Detector Solenoid

Design of a 15 T Hybrid Superconducting Magnet

Development of A Superconducting Solenoid for Cads

Fabrication and Test of a 1:4 Scaled HTS Coil for the Defocusing Magnet of 2 GeV FFAG Accelerator

Development of a 1/2-length prototype high field Nb3Sn magnet for the 4th generation ECR ion source

A Compact Superconducting Solenoid for China-ADS Injector II

A Superconducting Magnet with Center Field of 10 T and Φ100 Mm Warm Bore

Development and Testing of the Short Superconducting Magnets for ADS Injection I

Fabrication and cold test of prototype of spatially periodic radio frequency quadrupole focusing linac

Advances of the FRIB Project

Structural design and test of superconducting magnet coil for the cooling storage ring external-target experiment

Fabrication and Test of an 8-T Superconducting Split Magnet System with Large Crossing Warm Bore

Some Superconducting Magnets at IMP