Abstract:The effects of four different processes, direct quenching + tempering (DQ + T), direct quenching + reheating and quenching + tempering (DQ + RQ + T), forced air cooling + reheating and quenching + tempering (AC + RQ + T), and furnace cooling + reheating and quenching + tempering (FC + RQ + T), on microstructures and precipitates of Mo-Ti microalloyed medium carbon steel were investigated by OM, SEM, TEM, EBSD and mechanical tests. The width of martensite laths (0.22 +/- 0.01 mu m) produced in DQ + RQ + T was similar to that generated in DQ + T and was narrower than those formed during AC + RQ + T and FC + RQ + T. The effective grain size of the DQ + RQ + T sample was found to be the smallest (0.98 +/- 0.38 mu m), thus it yielded the finest (Ti, Mo) C precipitates, manifested high strength and excellent plastic toughness, and generated uniform transverse and longitudinal properties. The strength of the DQ + RQ + T sample (longitudinal R-m = 1773 MPa) was slightly lower than that of the DQ + T samples and its elongation (A = 11.0%) and impact energy at -40 degrees C (A(kv) = 50 J/cm(2)) were greater than those of the other three samples. Before the RQ process, the DQ cooling process was employed in order to generate large angle grain boundaries to provide more nucleation sites for austenitization. Moreover, the DQ process inhibited the precipitation of Ti during cooling and then formed fine (Ti, Mo) C precipitates during reheating of RQ to prevent austenite grain growth. Therefore, the DQ + RQ + T process generated fully refined austenite grains, made the martensite structure and (Ti, Mo) C precipitates more uniform, and enhanced the effects of fine grain strengthening and precipitation strengthening. In addition, the plasticity and the toughness of the fine and uniform equiaxed grains were also significantly improved, and the formation of acicular cementites was impeded.

Effect of Ta and Ti on Modified Reduced Activation Ferritic/Martensitic Steels with a Thermo‐mechanical Control Process

Effects of Cooling after Rolling and Heat Treatment on Microstructures and Mechanical Properties of Mo–Ti Microalloyed Medium Carbon Steel

Enhanced Disperse Ta(C, N) Precipitation in Reduced Activation Ferritic/martensitic Steels by Optimized Two-Step Austenitizing

Effect of TaC Particles Dissolution on Grain Coarsening in Reduced Activation Steels

Investigation on Precipitation Behaviors of MX Phase in Reduced Activation Steels

Thermo-Mechanical Processing as Method Decreasing Delta-Ferrite and Improving the Impact Toughness of the Novel 12% Cr Steels with Low N and High B Contents

Effect of Ta Addition on Mechanical Properties of 7715D Titanium Alloy

The effects of thermo-mechanical control process on microstructures and mechanical properties of a commercial pipeline steel

Microstructural Characteristic of Low Carbon Microalloyed Steels Produced by Thermo-Mechanical Controlled Process

Effect of thermo-mechanical treatment on Ti-Ta-Hf high temperature shape memory alloy

Effects of Novel Q-P-T and Traditional Q-T Processes on the Microstructure and Mechanical Properties of Martensitic Steels with Different Carbon Content

Effects of the titanium micro-alloying on the CG HAZ microstructure and toughness of the TMCP steels

Effect of carbon content and microstructural refinement on the mechanical property of quenching-partitioning - tempering-treated steels

Development of high strength plates with low yield ratio by the combination of TMCP and inter-critical quenching and tempering

Effect of Partitioning Treatment on the Mechanical Property of Fe-0.19c-1.47mn-1.50si Steel with Refined Martensitic Microstructure

Effects of Ti Addition on the Microstructure and Tensile Properties of China Low Activation Martensitic Steel for Nuclear Fusion Reactors

Effect of Hot-Rolling on the Microstructure and Impact Toughness of an Advanced 9%Cr Steel

Thermomechanical Processing of (tib + TiC)/Ti Matrix Composites and Effects on Microstructure and Tensile Properties

Importance of cold rolling and tempering on the microstructure evolution, precipitation behavior and mechanical responses of 9Cr3Co3W1Cu ferritic/martensitic steel

Relation Between Microstructure and Formability of Quenching-Partitioning-Tempering Martensitic Steel

New observations of the twinning effect and austenite stability in intercritical quenched and tempered steel with high strength