Proton irradiation induced phase transformation in Ni-Mn-Ga thin films

R. Ning,Z.P. Yang,Z.Y. Gao,X.Z. Cao,W. Cai

DOI: https://doi.org/10.1016/j.mseb.2021.115078

2021-01-01

Abstract:•The defects type induced by irradiation remains same and density elevates with dose.•The point defects generates compressive stress of 4 GPa in the film.•The sress by proton irradiation induces 7 M martensite formed in austenitic films.

What problem does this paper attempt to address?

Proton-irradiation-induced Structural and Magnetic Property Changes in Ni–Mn–Ga High-Temperature Shape Memory Films

Zhai-Ping Yang,Zhi-Yong Gao,Wei Cai

DOI: https://doi.org/10.1016/j.mseb.2017.06.004

2017-01-01

Abstract:Ni51.90Mn28.86Ga19.24 alloy films were irradiated by 120 keV protons at different fluences to investigate the effect of irradiation on their crystal structure, phase-transition temperature, and magnetic properties. The results show not only that a nanoscale amorphous layer may have been induced on the surface, but also that non-modulated (NM) martensite was produced. Moreover, differential scanning calorimetry peaks of the martensitic and austenitic transition temperatures are shifted to higher temperatures after irradiation; in particular, two endothermic and two exothermic peaks were observed for a proton fluence of 2.0 x 10(16)/cm(2). Further, the formation of NM martensite could produce an extra shoulder on the M-T curves of the irradiated films. Regarding the magnetic properties, a gradual decrease in the Curie temperature T-C can be caused by irradiation at a higher proton fluence. The changes in the saturation magnetization M-s with the proton fluence seem to be related to the reduction in T-C. (C) 2017 Elsevier B.V. All rights reserved.
The martensitic transformation of Ti–Ni shape memory thin films under proton irradiation

z y gao,h z wang,y y zhu,x l meng,wei cai

DOI: https://doi.org/10.1016/j.tsf.2015.01.023

IF: 2.1

2015-01-01

Thin Solid Films

Abstract:The martensitic transformation behavior of a Ti–Ni alloy irradiated by proton with different doses has been investigated. It is found that the samples irradiated by 150keV protons have a two-step phase transformation during heating and only one-step transformation during cooling. The exothermic peak at higher temperature disappears during the following thermal cycling. A model based on the stress-assisted martensitic transformation was established by the Transport of Ions in Matter (TRIM) calculations in order to explain the transformation behavior.
Microstructural Evolution and Phase Transformation in Proton-Irradiated NiTi Films

Xiaoyang Yi,Sibo Sun,Haizhen Wang,Zhiyong Gao,Wei Cai,Xin Zhang

DOI: https://doi.org/10.1016/j.intermet.2021.107305

IF: 4.075

2021-01-01

Intermetallics

Abstract:In the present work, the microstructural characteristics, martensitic transformation behavior, and mechanical performance of NiTi thin films irradiated with different proton fluences were investigated. Multiple-layer structures formed in the NiTi thin films owing to proton irradiation. As the proton fluences were 1.0 × 1015 p/cm2 and 5.0 × 1015 p/cm2, a two-layer structure containing a B2 phase and a B19’ martensite phase was introduced. In addition, thickness of B2 phase layer becomes larger and larger for irradiated NiTi thin films at room temperature, as the proton irradiation fluence increases. With further increasing proton irradiation fluence to 2.0 × 1016 p/cm2, an amorphous layer forms at the outmost layer of NiTi thin film. Moreover, an R phase and GP zones were detected in the interior of the B2 layer. The twin type of B19’ martensite also changed to release the stored elastic energy induced by proton irradiation. The martensite variant related (111‾) type I twins and the substructure of the <011> type II twins gradually evolved into (111) type I twins and (001) compound twins, respectively, with increasing proton irradiation fluence. The formation of a multiple-layer structure resulted in the presence of two endothermic and exothermic peaks corresponding to the B19’ ⇌ B2 martensitic transformation. The introduction of lattice defects was responsible for the reduction in the martensitic transformation temperature. The strength of the irradiated NiTi films was enhanced as a result of dislocation strengthening. However, the introduction of higher density of defects also leads to the deterioration of ductility.
Surface Modifications and Tailoring Magnetism in Ni48·4Mn28.8Ga22.8 Films by 120 Kev Proton Irradiation

Zhai-Ping Yang,Bin Sun,Zhi-Yong Gao,Wei Cai

DOI: https://doi.org/10.1016/j.intermet.2018.04.015

IF: 4.075

2018-01-01

Intermetallics

Abstract:Proton irradiation was performed to investigate the surface modifications and tailoring magnetism of ferromagnetic austenitic Ni48.4Mn28.8Ga22.8 films under different proton fluences. The X-ray diffraction (XRD) and transmission electron microscopy (TEM) results show that seven-layered modulated (7M) martensite can be produced on the surface of austenitic Ni48.4Mn28.8Ga22.8 films at the proton fluence values of 1.0 x 10(16) and 2.0 x 10(16) p/cm(2). The phase transformation temperatures and magnetic properties of the irradiated Ni48.4Mn28.8Ga22.8 films also depend on the proton fluence. Particularly, the magnetism of Ni48.4Mn28.8Ga22.8 films can be tailored by applying proton irradiation under different fluences. When the proton fluence is small as 1.0 x 10(15) p/cm(2), the saturation magnetization (M-s) and the magnetic anisotropy constant (K-1) of the irradiated Ni48.4Mn28.8Ga22.8 films can be improved. However, proton irradiation at a fluence as high as 2.0 x 10(16) p/cm(2) will deteriorate the magnetic performance of the Ni48.4Mn28.8Ga22.8 films. These experimental results are extremely meaningful to improve the magnetic-field-induced strain of Ni-Mn-Ga alloys via irradiation-induced modification or understand the damaged microstructure and magnetic properties of Ni-Mn-Ga alloys under extreme environment.
Effect of Proton Irradiation on Microstructural and Magnetic Properties of Ferromagnetic Ni–Mn–Ga Thin Films

Zhai-Ping Yang,Chang-Long Tan,Zhi-Yong Gao,Yuan Gao,Wei Cai

DOI: https://doi.org/10.1016/j.tsf.2017.04.032

IF: 2.1

2017-01-01

Thin Solid Films

Abstract:To explore the effect of proton irradiation on ferromagnetic Ni–Mn–Ga alloy, Ni54.5Mn26.3Ga19.2 thin films with the seven-layer modulated (7M) martensite structure were prepared by magnetron sputtering and irradiated by protons with an energy of 3MeV. The influence of proton irradiation on the microstructural and magnetic properties was investigated and discussed in detail. It is found that although nanoscale amorphous zones could be introduced by proton irradiation, the crystalline structure of the irradiated films retained the 7M martensite structure according to X-ray diffraction and transmission electron microscopy results. Moreover, the broad diffraction peak at 2θ=42.0° for the unirradiated films is split into two peaks at diffraction angles of about 41.5° and 42.2°, and the peak at 47.2° disappeared for the irradiated films. Regarding the magnetic properties, the irradiation-induced nanoscale amorphous defects may hinder the movement of magnetic domain walls, causing increases in the coercivity (Hc) and remanence (Mr). In addition, irradiation-enhanced thermal ordering will play a dominant role in improving the ordering of incompletely annealed films, ultimately resulting in slight increases in saturation magnetization (Ms) and the Curie temperature (Tc).
Formation of multilayer structure and evolution of shape recovery characteristics in proton irradiated TiNi alloy thin films

Yundong Zhao,Rui Ning,Xiaoyang Yi,Zhiyong Gao,Haizhen Wang,Wei Cai

DOI: https://doi.org/10.1016/j.matchar.2020.110348

IF: 4.537

2020-01-01

Materials Characterization

Abstract:TiNi thin films have attracted wide attentions as actuator materials in the micro-electro-mechanical systems (MEMs) for aerospace craft. However, multiple irradiation, such as the proton, was generally considered as an essential expired factor for the materials used in the aerospace. The present paper focused on the microstructure, martensitic transformation and shape recovery property of TiNi thin films after being irradiated by proton. A single layer structure B19′ phase to a dual-phase (B2 and B19′) with multilayer structure after proton irradiation have been revealed through a combination technique of grazing incidence (GI) XRD and TEM. As-formed irradiated films with amorphous layer and B2 austenite phase displayed a two-step martensitic transformation behavior, which occurred in the irradiated and the unirradiated layer. In contrast, the unirradiated counterparts just exhibited a single-step martensitic transformation. In addition, some defects could be seen after the TiNi films being irradiated. Such defects could induce a stress field that produces the R phase in the B2 phase. Furthermore, the synergistic effect of preferential sputtering effect and inverse Kirkendall effect induced the GP zones in the irradiated layer after 120 keV proton irradiation. The existence of amorphous phase and precipitation significantly deteriorated the shape recovery property.
Effect of 18 MeV Proton Irradiation on the R-phase Transformation in TiNi Shape Memory Alloys

ZG Wang,XT Zu,LJ Liu,S Zhu,Y Huo,LB Lin,XD Feng,LM Wang

DOI: https://doi.org/10.1016/s0168-583x(03)01279-5

2003-01-01

Abstract:Ti-50.6at.%Ni shape memory alloy specimens were irradiated in the parent phase using a tandem accelerator by 18 MeV protons at a dose rate of 4.27×109 cm−2s−1 for 1 h and 10 h, respectively. The total doses were 1.5×1013 and 1.5×1014 H+/cm2. Microstructures and phase transformation characteristics of the specimens before and after irradiations were evaluated by transmission electron microscopy and differential scanning calorimetry. There is no observable change of the microstructures after the irradiation. The parent phase (austenitic phase) was stabilized by the irradiation, since the R-phase transformation start temperature Rs and the reverse martensitic transformation finish temperature Af had decreased with increasing proton dose, about 6 K for Rs and 13 K for Af at a dose of 1.5×1014 H+/cm2. As and Rf were not affected by the proton irradiation. The variation of the transformation temperatures was assigned to local stress fields and changes in the degree of the lattice order produced by the proton irradiation.
Effect of Incomplete Transformation on the Transformation Behavior in Tini Shape Memory Alloys

Z. G. Wang,X. T. Zu

DOI: https://doi.org/10.1007/s10853-005-2100-y

IF: 2.1

2005-01-01

Thin Solid Films

Abstract:In this work, Ti–49.8 at.% Ni shape memory alloy (SMA) thin films were irradiated by 60-keV protons with two types of doses: 5×1016 and 1×1017 H+/cm2. The influence of proton irradiation on the transformation behavior of TiNi shape memory alloy films was investigated by differential scanning calorimetry (DSC) and glancing-incidence X-ray diffraction (GIXRD). The martensite transformation temperatures and austenite transformation temperatures shifted to lower value after proton irradiation, whereas proton irradiation has little effect on the R-phase transformation temperatures. This observation can be attributed to the formation of hydrides after proton irradiation.
Microstructure Evolution and Strain Recovery Characteristic of Proton-Irradiated Ti-rich NiTi Thin Films

Xiaoyang Yi,Sibo Sun,Bin Sun,Yundong Zhao,Rui Ning,Shangzhou Zhang,Zhiyong Gao,Haizhen Wang,Wei Cai

DOI: https://doi.org/10.1016/j.pnsc.2021.10.004

IF: 4.269

2021-01-01

Progress in Natural Science Materials International

Abstract:The effect of 120 ke V proton irradiation with different fluences on the phase constitution, microstructure, and shape recovery characteristics of Ni-51.4 at.%Ti shape memory alloy thin films was systematically investigated.The results showed that the proton irradiation induced the formation of a multiple-layer structure at the surface of Ni Ti thin film. Meanwhile, the hybrid defects such as vacancies, dislocations, and nano-scale precipitates were observed in the irradiation layer. The transition temperature and shape recovery strain decreased gradually with the increasing irradiation fluence, which can be attributed to the formation of the multilayer structure and the generation of irradiation-induced defects.
Atom redistribution and multilayer structure in NiTi shape memory alloy induced by high energy proton irradiation

Haizhen Wang,Xiaoyang Yi,Yingying Zhu,Yongkui Yin,Yuan Gao,Wei Cai,Zhiyong Gao

DOI: https://doi.org/10.1016/j.apsusc.2017.05.021

IF: 6.7

2017-01-01

Applied Surface Science

Abstract:The element distribution and surface microstructure in NiTi shape memory alloys exposed to 3 MeV proton irradiation were investigated. Redistribution of the alloying element and a clearly visible multilayer structure consisting of three layers were observed on the surface of NiTi shape memory alloys after proton irradiation. The outermost layer consists primarily of a columnar-like TiH2 phase with a tetragonal structure, and the internal layer is primarily comprised of a bcc austenite phase. In addition, the Ti2Ni phase, with an fcc structure, serves as the transition layer between the outermost and internal layer. The above-mentioned phenomenon is attributed to the preferential sputtering of high energy protons and segregation induced by irradiation. (C) 2017 Elsevier B.V. All rights reserved.
Effect of electron irradiation defects on the martensitic transformation characteristics and microstructure of Ni45Co5Mn37In13 alloys

Sibo Sun,Haixu Qin,Zhiyong Gao,Wei Cai,Xingzhong Cao

DOI: https://doi.org/10.1016/j.intermet.2022.107729

IF: 4.075

2022-01-01

Intermetallics

Abstract:Ni-Co-Mn-In based alloys with magnetically driven shape memory effect have shown its huge potential for applying as the intelligent driver in the spacecrafts. However, the numerous cosmic radiations, especially the electron irradiation with large penetration depth, could seriously harm its' serving stability. Herein, the Ni45Co5Mn37In13 alloys are exposed to the high energy electron irradiation with different fluence to study the phase transition behavior and microstructure evolution in the irradiation process. As a result, we reveal that the electron irradiation could induce dense crystal defects which not only reduce the transition temperature and thus retain the residual austenite in the martensitic matrix, but also destroy the continuity of martensitic laths and the atom arrangement in the twin boundaries. This work has important theoretical significance for understanding the electron irradiation's effect on the martensitic transformation and microstructure of Ni-Co-Mn-In alloys, and is conducive to expand martensitic transformation theory.
Effects of proton irradiation on the microstructure and shape recovery characteristics of a NiTi alloy

Haizhen Wang,Xiaoyang Yi,Yingying Zhu,Sibo Sun,Yuan Gao,Wei Cai,Z.Y. Gao

DOI: https://doi.org/10.1016/j.matchar.2018.04.001

IF: 4.537

2018-01-01

Materials Characterization

Abstract:Herein, we investigate the effects of proton irradiation on the structure and shape recovery characteristics of a NiTi alloy and provide a mechanistic explanation of the observed phenomena. Detailed analysis revealed that bombardment with 3 MeV protons induced the formation of a complex multilayer structure comprising TiH2, Ti2Ni, austenite and austenite-martensite layers along the irradiation direction with increasing distance and the origin of the above structure was shown to be closely related to the preferential sputtering effect and irradiation-induced segregation. Finally, the shape recovery characteristics significantly deteriorated with increasing irradiation fluence, since the multilayer structure hindered the martensitic transformation.
Structural transformation induced by nitrogen implantation in thin metal films

E. Ma,B.X. Liu,X. Chen,H.D. Li

DOI: https://doi.org/10.1016/0040-6090(87)90039-3

IF: 2.1

1987-01-01

Thin Solid Films

Abstract:High dose nitrogen implantation was carried out in gadolinium, cobalt, aluminium and copper thin films to study the implantation-induced phase formation. It is concluded that the presence or absence of an equilibrium nitride after implantation is directly related to the structural correlation between the metal matrix and the nitride. The formation of a nitride would be retarded or even inhibited if the required structural transformation is difficult to achieve. These results are believed to be attributable to the transient thermodynamic and kinetic conditions during ion irradiation.
Modified microstructures in proton irradiated dual phase 308L weldment filler material

Zhen Li,Xun Zhan,Xian-Ming Bai,Shao-Chun Lee,Weicheng Zhong,Benjamin J. Sutton,Brent J. Heuser

DOI: https://doi.org/10.1016/j.jnucmat.2021.152825

IF: 3.555

2021-05-01

Journal of Nuclear Materials

Abstract:The effect of proton irradiation on the microstructure of δ ferrite—γ austenite mixed phase 308L filler material in a 508-304 dissimilar metal weldment was investigated over a depth of 0 to 10 µm. Ni-Si-Mn G-phase precipitates were observed with SEM and TEM in δ ferrite but not in γ austenite. Our density functional theory based calculations show that the G/Fe interface energy in δ-Fe is significantly lower than that in γ-Fe (0.35 versus 1.25 J/m2), which provides a thermodynamics-based explanation for our experimental observations of preferential formation of G-phase in δ ferrite. STEM-EDS, TEM dark field imaging, and diffraction patterns confirmed the Ni-Si-Mn enriched precipitates were G-phase precipitates with a stoichiometry of Mn6Ni16Si7. Intragranular voids and Ni-Si enriched clusters were observed in irradiated γ austenite. Additionally, Ni and Si segregation was observed along the void interfaces. In both cases, Ni-Si clusters and segregation to voids, selected area diffraction patterns did not reveal the existence of a second phase. Proton irradiation induced Cr depletion and Si and Ni enrichment at γ−γ austenite grain boundaries that was characterized with STEM/EDS.

materials science, multidisciplinary,nuclear science & technology
Role of the X and N Factors in Ion-Irradiation Induced Phase Transformations of Mn+1AXn Phases

Chenxu Wang,Tengfei Yang,Cameron L. Tracy,Jingren Xiao,Shaoshuai Liu,Yuan Fang,Zhanfeng Yan,Wei Ge,Jianming Xue,Jie Zhang,Jingyang Wang,Qing Huang,Rodney C. Ewing,Yugang Wang

DOI: https://doi.org/10.1016/j.actamat.2017.11.008

IF: 9.4

2017-01-01

Acta Materialia

Abstract:Phase transitions induced in hcp M(n+1)AX(n) phases (Ti2AlN, Ti2AlC, and Ti4AlN3) by 1 MeV Au+ ion irradiation were investigated, over a series of ion fluences ranging from 1 x 10(14) to 2 x 10(16) ions cm(-2), by transmission electron microscopy (TEM) and synchrotron grazing incidence X-ray diffraction (GIXRD). Irradiation-induced structural evolutions were observed using high-resolution TEM (HRTEM) imaging and selected area electron diffraction (SAED). Based on phase contrast imaging and electron diffraction pattern (EDP) simulations, the atomic-scale mechanisms for the phase transitions were determined. Transformations of the initial hcp phases to the intermediate gamma-phases and fcc phases were driven by the formation of Ti/Al antisite defects and extended stacking faults induced by ion irradiation. By comparing the transformation behavior of Ti2AlN with that of Ti2AlC and Ti4AlN3 under the same irradiation conditions, using both the experimental data and first-principles calculations, the role of the X and n parameters in the radiation responses of M(n+1)AX(n) phases were elucidated. The susceptibilities of materials in this Ti-Al-X (X = C, N) system to irradiation-induced phase transitions were determined with respect to the bonding characteristics and compositions of these MAX phases. Ti2AlC is slightly less susceptible to the radiation-induced phase transformation than Ti2AlN, which is attributed to the stronger Ti-Al bond covalency in Ti2AlN. Ti4AlN3 is more resistant to radiation-induced phase transformations than is Ti2AlN, due to the lower Al content and lower anion vacancy ratio in the irradiation-induced solid solution phases. (C) 2017 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.
Influence of 60kev Proton Irradiation on the Transformation Behavior of a TiNi Shape Memory Alloy Thin Film

王治国,祖小涛,雷雨,莫华强,傅永庆

2004-01-01

High Power Laser and Particle Beams

Abstract:In this work, TiNi shape memory alloy films on oxidized single crystal Si substrate were successfully prepared by co-sputtering of TiNi target with a separated Ti target. The transformation behavior was investigated by differential scanning calorimeter (DSC) and in-situ XRD. 60 keV H~+ ions implantation shifted martensite transformation start/finish temperature M_s/M_f and austenite transformation start/finish temperature A_s/A_f to lower temperature, whereas H~+ implantation had little effect on the R-phase transformation temperatures R_s and R_f. glance incidence XRD results showed that titanium hydride formed after H~+ implantation .The change of transformation temperatures can be attributed to the formation of hydride.
Electron Irradiation Induced Multistage Martensitic Transformation in Ti‐Rich Ti−Ni Alloy

Yundong Zhao,Rui Ning,Zhiyong Gao,Haizhen Wang,Wei Cai

DOI: https://doi.org/10.1002/crat.202000035

2020-01-01

Crystal Research and Technology

Abstract:This paper focuses on the microstructure and martensitic transformation of titanium-nickel (Ti-Ni) alloys under electron irradiation. There is no observable change of the microstructure after irradiation. Abnormal multistage martensitic transformations are observed in Ti-rich Ti-48 at % Ni alloys after electron irradiation. The three-stage reverse martensitic transformation can be achieved in the irradiated alloy, while unirradiated counterpart displays normal one-stage transformation during heating processes. The abnormal reverse martensitic transformation behavior caused by electron irradiation is due to the local stress field and the excessive defect concentration. The martensitic transformation behavior and temperature after annealing at 250 degrees C are consistent with the unirradiated counterpart. Additionally, the irradiated alloy exhibits superior thermal cycle stability to unirradiated samples.
Site-specifically Controlling Phase Transformation Path in Ni2MnGa Shape Memory Alloy Through Ion Irradiation

Bin Chen,Chaoshuai Guan,Yikun Zhang,Shenghua Wu,Xuan Meng,Hongli Li,Gang Liu,Lingwei Li,Yong Peng

DOI: https://doi.org/10.1016/j.nantod.2024.102260

IF: 17.4

2024-01-01

Nano Today

Abstract:Reversible diffusionless martensitic transformation is the physical basis for the excellent properties of shape memory alloys. Precise control of transition behavior is generally regarded as an effective approach to improve the performance of alloys. Here, we propose a novel strategy to site-specifically control the transition behavior of Ni2MnGa shape memory alloy at the microscale. The nanoscale omega-like structure was found to appear and distribute uniformly in the parent matrix after high-energy ion beam irradiation, which resulted in the anisotropy of the {110} plane shuffling along the <110> direction. Consequently, the low-temperature phase of the sample changed from multi-variant five-layer modulated martensite to single-variant seven-layer modulated martensite. We further show that the specific phase transformation in Ni2MnGa shape memory alloys can be precisely controlled by the high-energy ion beam irradiation. This work should not only point out the potential risk of performance for the shape memory alloys serving in irradiation environments, but also contribute a novel way to fabricate more intelligent and specific-functional micro-/nano-devices of shape memory alloys.
Irradiation-induced Precipitation and Inverse Coarsening of G-phase in Austenitic Stainless Steel Weld Metal

Xiaodong Lin,Qunjia Peng,En-Hou Han,Wei Ke,Zhijie Jiao

DOI: https://doi.org/10.1016/j.matchar.2019.03.035

IF: 4.537

2019-01-01

Materials Characterization

Abstract:The irradiation-induced precipitation and inverse coarsening of G-phase in austenitic stainless steel weld metal were studied by using transmission electron microscopy and atom probe tomography. Following 0.5-dpa (displacement per atom) irradiation, Ni/Si/Mn/P-enriched G-phase was observed in delta-ferrite. By increasing the irradiation dose from 0.5 to 3 dpa, coarsening of G-phase occurred at first, followed by an obvious inverse coarsening. The segregation of Ni and Si atoms at alpha/alpha' interface due to spinodal decomposition was directly observed, which contributed to the G-phase precipitation. The inverse coarsening of G-phase was caused by irradiation recoil and could be interpreted by the cell model.
Site-specifically controlling phase transformation path in Ni 2 MnGa shape memory alloy through ion irradiation

Bin Chen,Chaoshuai Guan,Yikun Zhang,Shenghua Wu,Xuan Meng,Hongli Li,Gang Liu,Lingwei Li,Yong Peng

DOI: https://doi.org/10.1016/j.nantod.2024.102260

IF: 17.4

2024-04-10

Nano Today

Abstract:Reversible diffusionless martensitic transformation is the physical basis for the excellent properties of shape memory alloys. Precise control of transition behavior is generally regarded as an effective approach to improve the performance of alloys. Here, we propose a novel strategy to site-specifically control the transition behavior of Ni 2 MnGa shape memory alloy at the microscale. The nanoscale omega-like structure was found to appear and distribute uniformly in the parent matrix after high-energy ion beam irradiation, which resulted in the anisotropy of the {110} plane shuffling along the direction. Consequently, the low-temperature phase of the sample changed from multi-variant five-layer modulated martensite to single-variant seven-layer modulated martensite. We further show that the specific phase transformation in Ni 2 MnGa shape memory alloys can be precisely controlled by the high-energy ion beam irradiation. This work should not only point out the potential risk of performance for the shape memory alloys serving in irradiation environments, but also contribute a novel way to fabricate more intelligent and specific-functional micro-/nano-devices of shape memory alloys.

materials science, multidisciplinary,nanoscience & nanotechnology,chemistry

Proton irradiation induced phase transformation in Ni-Mn-Ga thin films

Proton-irradiation-induced Structural and Magnetic Property Changes in Ni–Mn–Ga High-Temperature Shape Memory Films

The martensitic transformation of Ti–Ni shape memory thin films under proton irradiation

Microstructural Evolution and Phase Transformation in Proton-Irradiated NiTi Films

Surface Modifications and Tailoring Magnetism in Ni48·4Mn28.8Ga22.8 Films by 120 Kev Proton Irradiation

Effect of Proton Irradiation on Microstructural and Magnetic Properties of Ferromagnetic Ni–Mn–Ga Thin Films

Formation of multilayer structure and evolution of shape recovery characteristics in proton irradiated TiNi alloy thin films

Effect of 18 MeV Proton Irradiation on the R-phase Transformation in TiNi Shape Memory Alloys

Effect of Incomplete Transformation on the Transformation Behavior in Tini Shape Memory Alloys

Microstructure Evolution and Strain Recovery Characteristic of Proton-Irradiated Ti-rich NiTi Thin Films

Atom redistribution and multilayer structure in NiTi shape memory alloy induced by high energy proton irradiation

Effect of electron irradiation defects on the martensitic transformation characteristics and microstructure of Ni45Co5Mn37In13 alloys

Effects of proton irradiation on the microstructure and shape recovery characteristics of a NiTi alloy

Structural transformation induced by nitrogen implantation in thin metal films

Modified microstructures in proton irradiated dual phase 308L weldment filler material

Role of the X and N Factors in Ion-Irradiation Induced Phase Transformations of Mn+1AXn Phases

Influence of 60kev Proton Irradiation on the Transformation Behavior of a TiNi Shape Memory Alloy Thin Film

Electron Irradiation Induced Multistage Martensitic Transformation in Ti‐Rich Ti−Ni Alloy

Site-specifically Controlling Phase Transformation Path in Ni2MnGa Shape Memory Alloy Through Ion Irradiation

Irradiation-induced Precipitation and Inverse Coarsening of G-phase in Austenitic Stainless Steel Weld Metal

Site-specifically controlling phase transformation path in Ni 2 MnGa shape memory alloy through ion irradiation