Abstract:Titanium alloys are widely used in various structural materials due to their lightweight properties. However, the low wear resistance causes significant economic losses every year. Therefore, it is necessary to implement wear-resistant protection on the surface of titanium alloys. In this study, four types of in situ composite ceramic coatings with two-layer gradient structures were prepared on a Ti-6Al-4V (TC4) substrate using laser cladding. In order to reduce the dilution rate, a transition layer (Ti-40SiC (vol.%)) was first prepared on TC4 alloy. Then, a high-volume-fraction in situ composite ceramic working layer (Ti-xFe-80SiC (vol.%)) with different contents of Fe-based alloy powder (x = 0, 5, 10 and 15 vol.%) was prepared. The working surface of Ti-40SiC (TL) exhibited a typical XRD pattern of Ti, TiC, Ti5Si3, and Ti3SiC2. In comparison, both Ti-80SiC (WL-F0) and Ti-5Fe-80SiC (WL-F5) exhibited similar phase compositions to the TL coating, with no new phase identified in the coatings. However, the TiFeSi2 and SiC phases were presented in Ti-10Fe-80SiC (WL-F10) and Ti-15Fe-80SiC (WL-F15). It is proven that the addition of the Fe element could regulate the in situ reaction in the original Ti-Si-C ternary system to form the new phases with high hardness and good wear resistance. The hardness of the WL-F15 (1842.9 HV1) is five times higher than that of the matrix (350 HV1). Due to the existence of self-lubricating phases such as Ti5Si3 and Ti3SiC2, a lubricating film was presented in the WL-F0 and WL-F5 coatings, which could block the further damage of the friction pair and enhance the wear resistance. Furthermore, a wear-transition phenomenon was observed in the WL-F10 and WL-F15 coatings, which was similar to the friction behavior of structural ceramics. Under the load of 10 N and 20 N, the wear volume of WL-F15 coating is 5.2% and 63.7% of that in the substrate, and the depth of friction of WL-15 coating is only 14.4% and 80% of that in the substrate. The transition of wear volume and depth can be attributed to the wear mechanism changing from oxidation wear to adhesive wear.

Study on the Microstructure and High Temperature Friction and Wear Characteristics of Three CVD Coated Cermets

Study on the growth and wear characters of CVD coating deposited on Ti(C, N)-based cermets with adding different C/N ratios of Ti(C, N) powders

Research On Wear Behavior Of Atc Cermet Material

Study on the growth and wear behavior of the TiAlN-based composite coating deposited on TiCN-based cermets with different binder phase

Friction and wear behavior of Ti(C,N) self-lubricating cermet materials with multilayer core-shell microstructure

Investigations on microstructure, mechanical and tribological properties of TiN coatings deposited on three different tool materials

Sliding friction behaviors of TiCN/Cr 3 C 2 -NiCr and TiCN/WC-CoCr duplex coatings fabricated by combining HVOF and HT-CVD procedures

Growth, mechanical properties, and tribological performance of TiAlN/NbN and NbN/TiAlN bilayer coatings

Tribological characteristics of WC-Cr3C2-Ni cermet coatings under different wear parameters

Microstructure and Wear Behavior of Ti-xFe-SiC In Situ Composite Ceramic Coatings on TC4 Substrate from Laser Cladding

Influence of film structure on the microstructure and properties of TiAlN coatings on Al-Si alloys

Microstructure and dry sliding wear behavior of laser clad AlCrNiSiTi multi-principal element alloy coatings

Microstructure and tribological properties of laser-cladded TiC x /TiAl composite coatings on TC4 alloy

Reciprocating Wear Performance and Interfacial Microstructure of a TiC–Ni 2 AlTi Cermet

Comparative investigation and characterization of the nano-mechanical and tribological behavior of RF magnetron sputtered TiN, CrN, and TiB2 coating on Ti6Al4V alloy

Development and Characterization of Laser Clad High Temperature Self-Lubricating Wear Resistant Composite Coatings on Ti–6Al–4V Alloy

Growth and properties of multi-layer nano CrAlN/TiAlN composite coating on the cermets with CrFeCoNiMo, CrFeCoNiMn, CrFeCoNiAl high entropy alloy phase

Microstructure and tribological behaviors of laser cladded CuAlMnTi–xTiC composite coatings at elevated temperature

Microstructure and tribological performance of Ni60-based composite coatings on Ti6Al4V alloy with different Ti3SiC2 ceramic additions by laser cladding

The Wear Behavior of the Laser Cladded Ti-Al-Si Composite Coatings on Ti-6Al-4V Alloy with Additional TiC

Development and characterization of Co-Cu/Ti3SiC2 self-lubricating wear resistant composite coatings on Ti6Al4V alloy by laser cladding