Abstract:The corrosion behaviour of different planes of a selective laser-melted (SLM) equimolar CrCoNi medium-entropy alloy (MEA) was investigated and compared with its counterpart cast alloy in a 3.5 wt% NaCl solution. The microstructures of the SLM products were characterised, and electrochemical corrosion measurements, corrosion surface morphology observations, and X-ray photoelectron spectroscopy analyses were performed. Compared with the cast MEA, the SLM MEA has an inferior corrosion resistance for its more metallurgical defects and smaller grain size. In the SLM MEA samples, The XY-plane of the SLM MEA has a poorer corrosion resistance than the XZ-plane, which is due to more metallurgical defects and lack of fusion pores on the XY-plane and its higher grain boundary density.

What problem does this paper attempt to address?

This paper aims to explore the corrosion performance of equimolar CrCoNi medium - entropy alloy (MEA) prepared by selective laser melting (SLM) in 3.5 wt% NaCl solution and compare it with the CrCoNi alloy prepared by the traditional casting process. Specifically, the research focuses on the following aspects: 1. **Material microstructure**: Characterize the microstructures of SLM and cast CrCoNi alloys, including grain size, metallurgical defects, etc., by means of X - ray diffraction (XRD), scanning electron microscope (SEM), energy - dispersive spectroscopy (EDS) and electron back - scatter diffraction (EBSD). 2. **Electrochemical corrosion behavior**: Evaluate the corrosion performance of different samples through open - circuit potential (OCP), electrochemical impedance spectroscopy (EIS) and potentiodynamic polarization curve tests. These tests can provide information on key parameters such as corrosion rate, corrosion current density, and passivation film stability. 3. **Corrosion surface morphology**: Observe the surface morphology after corrosion using SEM, analyze the distribution and morphology of corrosion products, and the formation mechanism of corrosion pits. 4. **Passive film characteristics**: Study the chemical composition and structural characteristics of the passive film formed during the corrosion process through X - ray photoelectron spectroscopy (XPS) analysis. The main conclusions of the paper are: - Due to more metallurgical defects and smaller grain size, the corrosion performance of CrCoNi alloy prepared by SLM is not as good as that of the cast CrCoNi alloy. - In SLM samples, the corrosion performance in the XY plane is worse than that in the XZ plane, which is mainly attributed to more metallurgical defects and higher grain boundary density on the XY plane. - The corrosion products formed during the corrosion process will accumulate around the corrosion pits, forming flocculent or reticular deposits, further affecting the corrosion performance of the material. Through these studies, the paper reveals the influence of the SLM process on the corrosion performance of CrCoNi alloy and provides a theoretical basis for optimizing SLM process parameters.

Corrosion performance of selective laser-melted equimolar CrCoNi medium-entropy alloy vs its cast counterpart in 3.5 wt% NaCl

Electrochemical Corrosion Behavior in Sulfuric Acid Solution and Dry Sliding Friction and Wear Properties of Laser-Cladded CoCrFeNiNb High Entropy Alloy Coatings

Corrosion Resistance Enhancement of Selective Laser Melted Cost‐Effective Interstitial Medium‐Entropy Alloy via Deep Cryogenic Treatment

Corrosion resistance enhancement of CoCrFeMnNi high-entropy alloy fabricated by additive manufacturing

Microstructure, Properties, and Metallurgical Defects of an Equimolar CoCrNi Medium Entropy Alloy Additively Manufactured by Selective Laser Melting

Distinction of Corrosion Resistance of Selective Laser Melted Al-12Si Alloy on Different Planes

A comparison of the mechanical and corrosion behavior of Fe49.5Mn25Cr15Ni10C0.5 medium-entropy alloy with its subsystems steels

Anisotropic Response of CoCrFeMnNi High-Entropy Alloy Fabricated by Selective Laser Melting

Corrosion behavior and mechanism of FeCrNi medium entropy alloy prepared by powder metallurgy

Corrosion Behavior of Selective Laser Melted AlSi10Mg Alloy in NaCl Solution and Its Dependence on Heat Treatment

Microstructure and corrosion behavior of Co-free FeCrNiSi0.4 medium entropy alloy coating fabricated by laser cladding

Densification, Microstructure and Anisotropic Corrosion Behavior of Al-Mg-Mn-Sc-Er-Zr Alloy Processed by Selective Laser Melting

Fabrication of iron-based amorphous reinforced CoCrNi medium-entropy alloys by selective laser melting: Enhancement of mechanical properties and improvement of corrosion resistance

Comparing the Corrosion Behavior of CoCrNi Medium-Entropy Alloy and Duplex Stainless Steel in Ammonium Chloride Solution

Distinction in Corrosion Resistance of Selective Laser Melted Ti-6Al-4V Alloy on Different Planes

A comparative study on the corrosion behavior of CoCrNi medium-entropy alloy and 316L stainless steel in simulated marine environment

The effect of Mn addition on corrosion behaviour of equiatomic CoCrFeNi high entropy alloys in NaCl solution

Microstructure and Corrosion Properties of Crmnfeconi High Entropy Alloy Coating

Comparative Study on Corrosion Behavior of As-Cast and Extruded Mg–5Y–7Gd–1Nd–0.5Zr Alloy in 5% NaCl Aqueous Solution

Microstructure, Mechanical and Corrosion Properties of Al–Co–Cr–Ni Near-Eutectic Medium Entropy Alloys

Effect of Cr Content on Microstructure, Mechanical, and Corrosion Properties of CoCr X FeMnNi High-Entropy Alloys Fabricated by Selective Laser Melting