Abstract:WC-Co cemented carbides are widely used in the fields of military, aerospace, mining and cutting industry etc. In this paper, a new two-step method for the preparation of WC-Co cemented carbides was proposed. First, the mixture of yellow tungsten trioxide (WO3) and cobaltic oxide (Co2O3) were reduced by carbon black to remove all the oxygen. Then, the carbothermic reduction products were precisely mixed with an appropriate amount of carbon black to directly prepare WC-Co cemented carbides. The effects of C/WO3 ratio on the phase composition, morphological evolution, particle size and mechanical properties of products are investigated. The experimental results revealed that when the C/WO3 molar ratio was above 2.7, all oxygen in the raw material mixture were removed by carbon black and a mixture of W2C and η-phase were obtained after the first step of carbothermic reduction at 1150 °C for 2 h; then, the mixture of carbothermic reduction product and an appropriate content of carbon black was compacted, and the green compact was first carbonized at 1200 °C for 2 h and then sintered at 1450 °C for 4 h to prepare cemented carbides. With the increase of C/WO3 ratio at the first stage, the content of η-phase with a low melting point increased, which resulted in the large grain size of WC in the finally prepared cemented carbide. Compared with the traditional method of preparing cemented carbides, the cemented carbides prepared by the current method showed a higher hardness and toughness. Furthermore, the addition of a proper content of the VC in the second stage can significantly inhibit the grain growth of WC and further increase the hardness of cemented carbides.

Research Status of WC-Co Cemented Carbide Prepared by Spark Plasma Sintering

Preparation of WC-Co Cemented Carbide by Spark Plasma Sintering: Microstructure Evolution, Mechanical Properties and Densification Mechanism

Spark Plasma Sintering of Ultrafine WC-5%Co Cemented Carbide Composite Powders

Rapid synthesis of ultrafine WC-Co cemented carbides by in-situ reactions and spark plasma sintering

In-Situ Synthesization of WC-6Co Cemented Carbides by SPS

Spark Plasma Sintering of Fine-Grained WC-Co Composites

Effect of Metal Elements on Microstructure and Mechanical Properties of Ultrafine Cemented Carbide Prepared by SPS

L1 2 strengthening of WC-CoNiFe cemented carbides by spark plasma sintering

Comparison of the microstructure and mechanical properties of WC-Ti(C, N)-Ni gradient cemented carbides prepared by SPS pre-sintering and vacuum pre-sintering

Ultrafine/nano WC-Co Cemented Carbide: Overview of Preparation and Key Technologies

Fabrication and performance of graded ultrafine WC–Co cemented carbide tool by one/two-step spark plasma sintering

Oscillatory Pressure Sintering: A New Method for Preparing WC-Co Cemented Carbides

Preparation of Ultra-Fine WC-Co Cermet and Its Wear Behavior

An investigation of the peculiarities of high-speed sintering of plasma chemically synthesized tungsten carbide nanopowders with increased oxygen content

Effect of Graphene on the Microstructure and Mechanical Properties of WC-Based Cemented Carbide

Effects of SiC addition on microstructure and properties of WC–6Co cemented carbide prepared by SPS

Effect of Y2O3 on microstructure and mechanical properties of WC-Co-cemented carbides prepared via solid-liquid doping method and spark plasma sintering

A short and facile process to synthesize WC-Co cemented carbides

Microstructure and mechanical properties of CoCrFeMnNi/WC plasma deposited coating after the spark plasma sintering treatment

Spark plasma sintered WC-Ni cemented carbides with various contents of ZrC nano-powder

Effect of Tungsten Carbide on Densification and Mechanical Properties of Silicon Nitride Ceramics by Spark Plasma Sintering