Abstract:Based on the results of current research and experiments, clock 135° hot rolling has been widely considered to be the preferred method in target rolling. However, it has been found that the process parameters are of vital importance during the rolling. Therefore, this work focuses mainly on the investigation of the effects of the roll speed ratio and offset distance on the microstructure evolution of a pure aluminum (Al) target under clock 135° collaborative hot rolling. Taking the ultra-thick pure Al metal circular billet as a research object, firstly, the evolutionary behavior of the effective strain (ES) and grain refinement for a rolled piece under the clock counterclockwise 135° synchronous and asynchronous (the speed ratios between rollers are set to be 1:1.05, 1:1.1, 1:1.2, respectively) rolling modes has been comparatively studied based on numerical simulation by DEFORM-3D software. It has been shown that a large ES value of 5.835 mm/mm is obtained in the lower surface layer by counterclockwise 135° asynchronous rolling with a roll–speed ratio of 1:1.2. Meanwhile, the average grain size below 80 μm accounts for ~61.8% of the total grains. These results demonstrate that the clock counterclockwise 135° asynchronous rolling method with a roll speed ratio of 1:1.2 should be an ideal strategy in obtaining finer grains. Unfortunately, nevertheless, the maximum degree of the bad plate shape is generated after forging by clock asynchronous rolling with a speed ratio of 1:1.2. As a consequence, clock counterclockwise 135° snake rolling with a 30 mm offset distance was proposed on the basis of a rolling speed ratio of 1:1.2, which perfectly corrected the warping plate shape caused by clock asynchronous rolling. What is more important, the minimum damage value of 1.60 was achieved accordingly. Meanwhile, the ES value increased in the core of the plate for the clock counterclockwise 135° snake rolling with all of the four offset distances compared to clock synchronous rolling. This study should be significantly conducive to guidance on setting process parameters in the industrial production of hot rolling metal or alloy targets.

Numerical simulation evolution of shear strain and crystallographic textures during snake rolling of Al-Mg-Si alloy plate

Microstructure, Texture Andmechanical Properties of Aa1060 Aluminum Plate Processed by Snake Rolling

Effects of rolling parameters of snake hot rolling on strain distribution of aluminum alloy 7075

Influence of Asymmetric Rolling on the Microstructure, Texture Evolution and Mechanical Properties of Al–Mg–Si Alloy

Crystal Plasticity Finite Element Simulation of Grain Evolution Behavior in Aluminum Alloy Rolling

Friction-mediated tuning of shear deformation and microstructure in asymmetrically rolled Mg–1Gd alloy strips

Effect of Rolling Strain on Microstructure and Tensile Properties of Dual-Phase Mg–8Li–3Al–2Zn–0.5Y Alloy

Dynamic recrystallization, texture and mechanical properties of high Mg content Al–Mg alloy deformed by high strain rate rolling

Microstructure, texture evolution and mechanical anisotropy of Mg-Gd-Y-Zn-Zr alloy sheets produced by unidirectional and cross rolling

Anisotropic Mechanical Behavior and Microstructural Characteristics of AA2099-T83 Alloy Sheet: Experiment and Simulation

Shear Deformation and Grain Refinement in Pure Al by Asymmetric Rolling

Analysis of Temperature Asymmetry of Aluminum Alloy Thick Plate During Snake Hot Rolling

Interpretation of the strain state during cross-roll rolling of aluminum by means of texture analysis

Calculation and analysis of rolling force during aluminum alloy thick plate snake/gradient temperature rolling with different roll diameters

Bending analysis and control of rolled plate during snake hot rolling

Rolling texture development in a dual-phase Mg-Li alloy: The role of temperature

Improved Mechanical Anisotropy and Texture Optimization of a 3xx Aluminum Alloy by Differential Temperature Rolling

Effect of Direction Change of Shear Deformation on the Textures in Rolled High Purity Al

Effects of Process Parameters on Microstructure Evolution of Pure Aluminum Target under Clock 135° Collaborative Hot Rolling: A Simulation Study

Unveiling the Rolling Texture Variations of Α-Mg Phases in a Dual-Phase Mg-Li Alloy

Revealing the Microstructure Evolution Mechanism and Mechanical Responses of a Novel Al–Zn–Mg–Cu Alloy by Hot Deformation Process