Abstract:The effects of temperature on the tribological and dynamic mechanical properties (DMP) of aromatic liquid-crystal poly(ester-co-amide) were investigated. Specimens for the DMA test and friction and wear test were prepared by compression molding at elevated temperature. The dynamic mechanical properties of the resulting compression-molded liquid crystal polymer (LCP) specimens were evaluated on a Perkin-Elmer DMA instrument, in a three-point bending mode, at a heating rate of 10°C/min and frequency of 1Hz from room temperature to 250°C. The friction and wear behavior of the compression-molded LCP specimens sliding against SA52100 steel in a ball-on-disk configuration was evaluated on a high-temperature friction and wear tester from 25 to 300°C. The worn surface morphologies of the compression-molded LCP specimens were observed on a scanning electron microscope. It was found that the tribological and dynamic mechanical properties of the LCP strongly depended on the test temperature. Namely, the friction coefficients decreased significantly and the wear rate increased considerably with increasing temperature. This was attributed to the enhanced softening and plastic deformation of the LCP at elevated temperature. The LCP experienced severe plastic deformation, flowing and local melting owing to the destruction of the stiff backbones of the polymeric molecules at excessively high temperature, thus the largest wear rate of the tested LCP was generated at 300°C. Such a trend in the friction and wear behavior of the compression-molded LCP with temperature conformed well to the corresponding worn surface morphologies. Namely, the LCP worn surface was characterized by mild plastic deformation and micro-cracking as the LCP disk slid against the steel ball at 50°C, whilst at 100°C, the plastic deformation and adhesion became severe and the micro-cracking disappeared owing to the plastic flow. The plastic deformation and adhesion became increasingly more severe with further increase of the test temperature up to 150, 200, and 250°C, owing to the increased plastic flow and local softening and melting of the LCP. Moreover, the storage modulus of the compression-molded LCP greatly decreased with increasing temperature, as did the loss modulus, while the complex modulus and tan δ increased with increasing temperature, which agreed well with the corresponding trend of the tribological behavior with temperature. It was confirmed that the dynamic mechanical properties of the polymer were an important factor of the high temperature tribological behavior.

Effects of Friction Heat on Tribological Properties of UHMWPE

Effect of Temperature on the Tribological and Dynamic Mechanical Properties of Liquid Crystalline Polymer

Modeling of contact temperatures and their influence on the tribological performance of PEEK and PTFE in a dual-pin-on-disk tribometer

Effect of the Thermal Conductivity of Mated Materials on the Wear Intensity of a Polymerpolymer Friction Pair

Analysis of Temperature and Heat Partitioning Coefficient During Friction Between Polymer and Steel

The Relationships Between Tribological Behaviour and Heat-Transfer Capability of Ti6Al4V Alloys

Effect of temperature on the tribological properties of Polytetrafluoroethylene/Kevlar fabric/phenolic composites

Effect of thermorheological properties on tribological behaviors of lubricating grease

Impact of thermo-oxidative aging on the dry tribological performance and wear mechanisms of UHMWPE/ZrO2 friction pairs

Friction and Temperature Behavior of Lubricated Thermoplastic Polymer Contacts

The effect of temperature on the tribological characteristics of high speed steels under conditions of friction without lubricant on the structural steel 30HGSA

Effect of temperature on the friction and wear properties of a crosslinked and a linear polyimide

Study on Tribological Characteristics of Ultra-High Molecular Weight Polyethylene under Unsaturated Lubrication of Water and Brine

Study of Friction and Wear Characteristics of PEEK by Reciprocating Sliding Experiment and Temperature Dependences Simulation

Wear Rate, Frictional Temperature, and Energy Consumption of Steel 52100 with Different Microstructures During Sliding

Experimental and Finite Element Analysis of Frictional Heat Distribution during Sliding Friction

Significant sliding speed effect on the friction and wear behavior of UHMWPE matrix composites

Improved Tribological Properties of Poly(methyl methacrylate) Based Composites by the Synergistic Effect of Incorporating Ultra-High Molecular Weight Polyethylene and Heat Treatment

Tribological evaluation of thermoplastic polyurethane-based bearing materials under water lubrication: Effect of load, sliding speed, and temperature

Effect of temperature on friction and wear of polyimide

Effect of crystalline form on the tribological properties of PA46/HDPE polyblends