Abstract:The effects of temperature on the tribological and dynamic mechanical properties (DMP) of aromatic liquid-crystal poly(ester-co-amide) were investigated. Specimens for the DMA test and friction and wear test were prepared by compression molding at elevated temperature. The dynamic mechanical properties of the resulting compression-molded liquid crystal polymer (LCP) specimens were evaluated on a Perkin-Elmer DMA instrument, in a three-point bending mode, at a heating rate of 10°C/min and frequency of 1Hz from room temperature to 250°C. The friction and wear behavior of the compression-molded LCP specimens sliding against SA52100 steel in a ball-on-disk configuration was evaluated on a high-temperature friction and wear tester from 25 to 300°C. The worn surface morphologies of the compression-molded LCP specimens were observed on a scanning electron microscope. It was found that the tribological and dynamic mechanical properties of the LCP strongly depended on the test temperature. Namely, the friction coefficients decreased significantly and the wear rate increased considerably with increasing temperature. This was attributed to the enhanced softening and plastic deformation of the LCP at elevated temperature. The LCP experienced severe plastic deformation, flowing and local melting owing to the destruction of the stiff backbones of the polymeric molecules at excessively high temperature, thus the largest wear rate of the tested LCP was generated at 300°C. Such a trend in the friction and wear behavior of the compression-molded LCP with temperature conformed well to the corresponding worn surface morphologies. Namely, the LCP worn surface was characterized by mild plastic deformation and micro-cracking as the LCP disk slid against the steel ball at 50°C, whilst at 100°C, the plastic deformation and adhesion became severe and the micro-cracking disappeared owing to the plastic flow. The plastic deformation and adhesion became increasingly more severe with further increase of the test temperature up to 150, 200, and 250°C, owing to the increased plastic flow and local softening and melting of the LCP. Moreover, the storage modulus of the compression-molded LCP greatly decreased with increasing temperature, as did the loss modulus, while the complex modulus and tan δ increased with increasing temperature, which agreed well with the corresponding trend of the tribological behavior with temperature. It was confirmed that the dynamic mechanical properties of the polymer were an important factor of the high temperature tribological behavior.

Effect of temperature on friction and wear of polyimide

Effect of temperature on the friction and wear properties of a crosslinked and a linear polyimide

Effect of Temperature on the Tribological and Dynamic Mechanical Properties of Liquid Crystalline Polymer

Effect of temperature on the friction and wear performance of porous oil-containing polyimide

Tribophysical and tribochemical effects of a thermoplastic polyimide

Tribological Behaviors of Fluorinated Polyimides at Different Temperatures

Effect of temperature on the tribological properties of Polytetrafluoroethylene/Kevlar fabric/phenolic composites

Exploring the Friction and Wear Behaviors of Ag-Mo Hybrid Modified Thermosetting Polyimide Composites at High Temperature

Tailoring Polyimide Composites with Low Friction and Wear at High Temperatures

Effect of Atomic Oxygen on Corrosion and Friction and Wear Behavior of Polyimide Composites

Evolution of the Low-Temperature Tribological Performance of Polychlorotrifluoroethylene and Polyimide

Investigation on Tribological Properties of Fluorinated Polyimide

Wear Evolution of the Glass Fiber-Reinforced PTFE under Dry Sliding and Elevated Temperature

Effect of Temperature on Wear Behavior in a Ti-V-Cr Base Fireproof Titanium Alloy

Thermomechanical and tribological properties of polyimide and polyethersulfone blends reinforced with expanded graphite particles at various elevated temperatures

The influence of temperature on the tribological properties of polyoxymethylene (POM) materials

Study of Friction and Wear Characteristics of PEEK by Reciprocating Sliding Experiment and Temperature Dependences Simulation

Study on the Rheological Properties of Fluorinated Polyimide Spinning Solution

Wear failure mechanism analysis of self-lubricating fabric composites at high temperature

Improving Thermal Conductivity and Tribological Performance of Polyimide by Filling Cu, CNT, and Graphene

Tribological Properties of Carbon Fiber Epoxy Resin Composite and Polyimide Material at High and Low Temperatures