Abstract:The effects of temperature on the tribological and dynamic mechanical properties (DMP) of aromatic liquid-crystal poly(ester-co-amide) were investigated. Specimens for the DMA test and friction and wear test were prepared by compression molding at elevated temperature. The dynamic mechanical properties of the resulting compression-molded liquid crystal polymer (LCP) specimens were evaluated on a Perkin-Elmer DMA instrument, in a three-point bending mode, at a heating rate of 10°C/min and frequency of 1Hz from room temperature to 250°C. The friction and wear behavior of the compression-molded LCP specimens sliding against SA52100 steel in a ball-on-disk configuration was evaluated on a high-temperature friction and wear tester from 25 to 300°C. The worn surface morphologies of the compression-molded LCP specimens were observed on a scanning electron microscope. It was found that the tribological and dynamic mechanical properties of the LCP strongly depended on the test temperature. Namely, the friction coefficients decreased significantly and the wear rate increased considerably with increasing temperature. This was attributed to the enhanced softening and plastic deformation of the LCP at elevated temperature. The LCP experienced severe plastic deformation, flowing and local melting owing to the destruction of the stiff backbones of the polymeric molecules at excessively high temperature, thus the largest wear rate of the tested LCP was generated at 300°C. Such a trend in the friction and wear behavior of the compression-molded LCP with temperature conformed well to the corresponding worn surface morphologies. Namely, the LCP worn surface was characterized by mild plastic deformation and micro-cracking as the LCP disk slid against the steel ball at 50°C, whilst at 100°C, the plastic deformation and adhesion became severe and the micro-cracking disappeared owing to the plastic flow. The plastic deformation and adhesion became increasingly more severe with further increase of the test temperature up to 150, 200, and 250°C, owing to the increased plastic flow and local softening and melting of the LCP. Moreover, the storage modulus of the compression-molded LCP greatly decreased with increasing temperature, as did the loss modulus, while the complex modulus and tan δ increased with increasing temperature, which agreed well with the corresponding trend of the tribological behavior with temperature. It was confirmed that the dynamic mechanical properties of the polymer were an important factor of the high temperature tribological behavior.

Effect of temperature on the friction and wear performance of porous oil-containing polyimide

Effect of Temperature on the Tribological and Dynamic Mechanical Properties of Liquid Crystalline Polymer

Effect of temperature on friction and wear of polyimide

Effect of temperature on the friction and wear properties of a crosslinked and a linear polyimide

Effect of Lubricating Condition on Tribological Properties of Nano-SiO2 Filled Polyamide Composite

Tribological properties of oil-impregnated polyimide in double-contact friction under micro-oil lubrication conditions

Tribophysical and tribochemical effects of a thermoplastic polyimide

Effects of porosity on the tribological and mechanical properties of oil-impregnated polyimide

The influence of temperature on the tribological properties of polyoxymethylene (POM) materials

Role of transfer film formation on the tribological properties of polymeric composite materials and spherical plain bearing at low temperatures

Effect of temperature on the tribological properties of Polytetrafluoroethylene/Kevlar fabric/phenolic composites

Research on the Effect of Temperature on Tribological Properties of PTFE Composites under Oil Lubrication Conditions

Tribological Behaviors of Fluorinated Polyimides at Different Temperatures

Tailoring Polyimide Composites with Low Friction and Wear at High Temperatures

Exploring the Friction and Wear Behaviors of Ag-Mo Hybrid Modified Thermosetting Polyimide Composites at High Temperature

The investigation of tribological properties of PAI/PI‐EPN polymer coating filled with WS2 and SiC at low temperatures

Effects of the Mesoporous Filler and Oleophilic Property on the Tribological Behavior of Polyetheretherketone Composites.

Tribological behavior and mechanism of Mo2Ti2C3/polyimide composite films under dry friction condition

2D Mo2CTx Reinforced Polyimide Nanocomposites for Enhancement of Surface Tribological Performance at Elevated Temperatures

Preparation and tribological properties of porous polyimide modified by graphene

Effect of Atomic Oxygen on Corrosion and Friction and Wear Behavior of Polyimide Composites