Abstract:Vinyl chloride/ N-phenylmaleimide copolymer ( VC/PMI) and vinyl chloride/ N-phenylmaleimide/ acrylonitrile terpolymer (VC/PMI/AN) were synthesized in the suspension copolymerization process for improving the heat resistance of poly( vinyl chloride) PVC) This paper emphasized on the studies on the characterization of the heat resistant properties of these three co) polymers mainly by means of dynamic mechanical experiment with the change of storage modulus ( E'), change rate of E' with temperature and mechanical loss factor ( tandelta) near the glass transition. The Vicat softening point ( VSP) was also tested supplementally for comparison. The lower the change rate of E' with temperature is, the higher the heat resistance of VC/PMI and VC/PMI/AN will be. The effects of the amount of PMI and AN in the recipes of copolymerization on the change rate of E' with temperature, tandelta and VSP were also investigated. The results show that the increase of the amount of PMI will increase the rigidity of the backbone of the copolymer chain so as to improve the heat resistance. On the other hand, the introduction of AN into the copolymer will give more uniform distribution of PMI unit or segment in the backbone, and thus improves the heat resistance of the copolymer further. It is discovered that there are two peaks of mechanical loss or two glass transition temperatures of VC/PMI/AN copolymerization product. It may be interpreted from the higher reactivities of PMI and AN than VC. During the copolymerization process of VC, PMI and AN, the more active PMI and AN will copolymerize more rapidly and will consume entirely at conversion of about 45% similar to 50%. Thereafter, VC continues to homopolymerize to form PVC homopolymer until a final conversion of 85%. Actually, the final product is a mixture of VC/PMI/AN terpolymer and homo-PVC, showing two T(g)s.

Principle and Application of Composition Distribution Measurement for Vinyl s/N-Phenyl mai eimide Copolymer

Mechanism and kinetics of emulsion copolymerization of vinylidene chloride—Critical conversion at the end of interval 2 and rate of polymerization

Online Monitoring Of Drop/Particle Size And Size Distribution In Liquid-Liquid Dispersions And Suspension Polymerizations By Optical Reflectance Measurements

A New Theoretical Formula for the Determination of the Copolymer Composition Distribution Measured by Gel Permeation Chromatography

Research of Styrene/Aerylonitrille/N-Phenlymaleimide Emalsion Copolymerization

Solvent Concentration Distribution in Acetone/PMMA Coating Solution Measured by Laser Confocal Raman Spectroscopy Method

Measurement and Model of Molecular Weight for Styrene/N-Phenylmaleimide Copolymer

Measurement and model of molecular weight for Styrene/N-Phenyl maleimide copolymer

Control and Optimization for Vinyl Chloride/N-Phenylmaleimide Copolymer Composition

Prediction, Control and Optimization for Vinyl Monomer/N-Phenylmaleimide Copolymers Composition

Study on Suspension Copolymerization Rate of Vinyl Chloride/n-Phenylmaleimide

Determination of acetone content in PMMA/acetone coating solution by Raman peak contrast method

Numerical Simulation on Solvent Diffusion during Polymeric Coating Curing Processes

Bivariate Distribution in PMMA/PBA Copolymers by Combined SEC/NMR and SEC/MALDI Measurements

Heat Resistant Properties of Vinyl Chloride-N-Phenylmaleimide (-Acrylonitrile) Suspension Polymerized Copolymer

Studies on the Microstructure of Vinyl/N-Phenylmaleimide Copolymers by Nmr and Their Applications

Studies on the Glass Transition Temperature of VC/PMI Copolymer

Studies on the Sequence Structure of Vinyl Monomer-N-Phenylmaleimide Copolymers

Mutual Solubility And Bulk Copolymerization Of Vinyl Monomers With N-Substituted Maleimide

A Segment Probability Method for Calculating the Molecular Weight Distributions of Linear Polycondensates in a Continuous Reactor

Kinetics of Vinylidene Chloride / Acrylonitrile / Styrene Suspension Polymerization