Abstract:Objective: This study was designed to show that the commonly reported irradiance values that are quoted in most publications inadequately describe the light output from light curing units (LCUs). Methods: The total spectral radiant power (mW) output from 12 contemporary LCUs was measured with a fiberoptic spectroradiometer and a calibrated integrating sphere. Five recordings were taken for each LCU and exposure mode. In addition, the irradiances (mW/cm²) delivered at 0-mm, 5-mm and 10-mm distances were recorded through a 6-mm diameter aperture and the radiant exposures (J/cm²) from the LCUs were calculated. Light beam profiles from the LCUs were recorded using a beam profiler, and the images were overlaid on a molar tooth to simulate a clinical setting. Data were analyzed using ANOVA followed by Tukey post-hoc test (α = 0.05). Results: The mean power outputs from the LCUs ranged from 380 to 2472 mW (p < 0.0001). The highest irradiance was recorded from the Cicada CV 215-G7 (3091 mW/cm² in its highest mode) and the lowest from the Radii Cal CX (731 mW/cm²). The emission spectra differed, even among the multi-peak and single-peak LCUs. Radiant exposures from the entire light tip ranged from 18.3 J/cm², Radii Cal CX, in its standard 25 s exposure mode to 3.9 J/cm² from the Monet Laser in a 3 s exposure setting. Half (50 %) of the measured irradiance values from the LCUs differed from the manufacturers' value by more than 10 %. There were significant differences in the impact of distance from the tip. The beam profiles visually highlighted the varying effects of distance from the LCU tip among different units. Conclusion: There were significant differences in the emission spectra, power outputs, tip diameters, irradiances, radiant exposures, and the effect distance from the light tips. These differences underline the importance of manufacturers and researchers correctly measuring and reporting the output from the LCU to ensure that research is reproducible and that patients receive acceptable dental restorations. Clinical significance: This article alerts clinicians, researchers and journal editors that providing only the tip irradiance (radiant exitance) value from the LCU is no longer sufficient. Manufacturers and researchers should include information on the spectral radiant power, emission spectrum, tip diameters, and also the effect of distance on the irradiance and radiant exposure, beam profiles and tooth access information when describing an LCU.

Analysis of factors influence the power density of light curing units

[A Survey of Power Density of Clinical Curing-Light Units Used in Changchun].

A survey of power density of light-curing units used in private dental offices in Changchun City, China

Composite Cure and Pulp-Cell Cytotoxicity Associated with LED Curing Lights.

Curing performance of three different curing lights at different distances for a resin composite

Curing Efficiency of Three Different Curing Lights at Different Distances for A Hybrid Composite

Power Outputs and Clinical Use of Light Cure Units

[Optical Properties of LED Light Curing Unit Before and after Transmitting Different Colors and Thickness of Two Kinds of Glass Ceramics].

The dark art of light curing in dentistry

[Effect of Light Power Density on the Anti-Aging Property of Light-Cure Composite Resin].

Curing Efficiency of Three Different Curing Modes at Different Distances for Four Composites

Influence of Different Power Density and Shades on the Microhardness of Nano-composite Resins at Different Energy Level

The effect of distance from light source on the light intensity decrease of six LED light units

Effect of Battery Level During Successive Charging Cycles on the Performance of Certified and Low-cost Uncertified Light-curing Units Available on E-commerce

Light curing unit effectiveness assessed by dental radiometers

Impact of Battery Levels of a Cordless LED Curing Unit on Resin Cement under Varied Lithium Disilicate Thicknesses and Translucencies

High Power-density UV-LED Package Modules and Their Application in Curing

High-Power LED Units Currently Available for Dental Resin-Based Materials—A Review

The comparison of cure depth and surface hardness of composite resin cured with two kinds of new curing lights and traditional halogen curing light

Clinical effectiveness of light-curing units of the School of Dentistry of the Federal University of Goias

Effects of light-curing modes on the polymerization shrinkage and surface hardness of composite resins]