Abstract:Objectives This study investigated effects of the different emittance-mode protocols from three light curing units (LCUs): (i) a Laser (Monet); (ii) a quad-wave (PinkWave); (iii) a conventional LED (Elipar S10) on the temperature rise (ΔT) and degree of conversion (DC) when photo-curing fast or conventional bulk-fill resin-based composites (RBC). The aim was to correlate ΔT and DC, and the radiant exposure delivered to RBC specimens. Methods A 3D-printed resin mold of 4 mm depth was filled with two bulk-fill RBCs: Tetric PowerFill® ( fast photo-polymerised composite) ( TPF ) or Tetric EvoCeram® Bulk-Fill ( EVO ). Three LCUs were used: (i) Monet laser for 1 s and 3 s ( MONET-1 s, MONET-3 s ); (ii) PinkWave quad-wave used for 3 s in Boost mode ( PW-3 s ) and for 20 s in standard mode ( PW-20 s ); (iii) Elipar S10 for 5 s ( S10–5 s ) and for 20 s in standard mode ( S10–20 s ). 2-dimensional temperature maps were obtained before, during and for 60 s after the LCU had turned off using a thermal imaging camera. Thermal changes were analysed at five depths: (0, 1, 2, 3, and 4 mm from the top surface of the RBC). The maximum temperature rise ( T max ) and the mean temperature rise ( ΔT ) were determined. Cylindrical-shaped specimens were prepared from each material using a stainless-steel split mold (4 × 4 mm) and light-cured with the same protocols. The DC was measured for 120 s and at 1 h after LCU had turned off using Fourier Transform Infrared Spectroscopy (FTIR). Data were analysed using Three-way ANOVA, One-way ANOVA, independent t-tests, and Tukey post-hoc tests (p < 0.05). Results Radiant exposures delivered by the various irradiation protocols were between 4.5–30.3 J/cm 2 . Short exposure times from MONET-1 s and PW-3 s delivered the lowest radiant exposures (4.5 and 5.2 J/cm 2 , respectively) and produced the lowest ΔT and DC. The longer exposure times in the standard modes of PW-20 s, S10–20 s, and MONET-3 s produced the highest T max , ΔT, and DC for both composites. The ΔT range among composites at different depths varied significantly (31.7–49.9 °C). DC of TPF ranged between 30–65% and in EVO between 15.3–56%. TPF had higher T max, ΔT for all depths and DC compared to EVO, across the LCU protocols (p < 0.05), except for PW-20 s and MONET-3 s. The coronal part of the restorations (1–2 mm) had the highest ΔT. There was a positive correlation between ΔT and DC at 4-mm depth after 120 s Significance Longer, or standard, exposure times of the LCUs delivered greater radiant exposures and had higher DC and ΔT compared to shorter or high-irradiance protocols. The fast photo-polymerised RBC had comparatively superior thermal and conversion outcomes when it received a high irradiance for a short time (1–5 s) compared to the conventional Bulk-Fill RBC.

Light curing unit effectiveness assessed by dental radiometers

Composite Cure and Pulp-Cell Cytotoxicity Associated with LED Curing Lights.

The dark art of light curing in dentistry

Curing Efficiency of Three Different Curing Lights at Different Distances for A Hybrid Composite

[The type testing of light-polymerization equipment, I: the testing protocol]

Curing performance of three different curing lights at different distances for a resin composite

Effects of Light Attenuation through Dental Tissues on Cure Depth of Composite Resins

Power Outputs and Clinical Use of Light Cure Units

Dual-cure dental composites: can light curing interfere with conversion?

Ability of Six Curing Lights to Photocure Four Resin-Based Composites in a MOD-Mold: A Double-Blind Study

Beam profile measurements for dental phototherapy: the effect of distance, wavelength and tissue thickness

Thermography and conversion of fast-cure composite photocured with quad-wave and laser curing lights compared to a conventional curing light

Knowledge and Attitude of Dental Clinicians towards Light-Curing Units: A Cross-Sectional Study

Comparison of the mechanical properties of composite resin cured by halogen curing light with those by LED curing light

The Effects of Intensity, Exposure Time, and Distance of Polymerization Light on Vickers Microhardness and Temperature Rise of Conventional Resin-Based Composite

Impact of Battery Levels of a Cordless LED Curing Unit on Resin Cement under Varied Lithium Disilicate Thicknesses and Translucencies

The Effect of Two Different Light-Curing Units and Curing Times on Bulk-Fill Restorative Materials

The Effect of Light-emitting Diode Light Intensities and Duration of Cure on Pulpal Wall Temperature among Different Classes of Teeth

Effect of Different Post-Curing Methods on the Degree of Conversion of 3D-Printed Resin for Models in Dentistry

The survey of various Light-curing units applied to the compomer restoration of primary teeth.

Effects of Post-Curing Light Intensity on the Mechanical Properties and Three-Dimensional Printing Accuracy of Interim Dental Material