Abstract:Objectives This study investigated effects of the different emittance-mode protocols from three light curing units (LCUs): (i) a Laser (Monet); (ii) a quad-wave (PinkWave); (iii) a conventional LED (Elipar S10) on the temperature rise (ΔT) and degree of conversion (DC) when photo-curing fast or conventional bulk-fill resin-based composites (RBC). The aim was to correlate ΔT and DC, and the radiant exposure delivered to RBC specimens. Methods A 3D-printed resin mold of 4 mm depth was filled with two bulk-fill RBCs: Tetric PowerFill® ( fast photo-polymerised composite) ( TPF ) or Tetric EvoCeram® Bulk-Fill ( EVO ). Three LCUs were used: (i) Monet laser for 1 s and 3 s ( MONET-1 s, MONET-3 s ); (ii) PinkWave quad-wave used for 3 s in Boost mode ( PW-3 s ) and for 20 s in standard mode ( PW-20 s ); (iii) Elipar S10 for 5 s ( S10–5 s ) and for 20 s in standard mode ( S10–20 s ). 2-dimensional temperature maps were obtained before, during and for 60 s after the LCU had turned off using a thermal imaging camera. Thermal changes were analysed at five depths: (0, 1, 2, 3, and 4 mm from the top surface of the RBC). The maximum temperature rise ( T max ) and the mean temperature rise ( ΔT ) were determined. Cylindrical-shaped specimens were prepared from each material using a stainless-steel split mold (4 × 4 mm) and light-cured with the same protocols. The DC was measured for 120 s and at 1 h after LCU had turned off using Fourier Transform Infrared Spectroscopy (FTIR). Data were analysed using Three-way ANOVA, One-way ANOVA, independent t-tests, and Tukey post-hoc tests (p < 0.05). Results Radiant exposures delivered by the various irradiation protocols were between 4.5–30.3 J/cm 2 . Short exposure times from MONET-1 s and PW-3 s delivered the lowest radiant exposures (4.5 and 5.2 J/cm 2 , respectively) and produced the lowest ΔT and DC. The longer exposure times in the standard modes of PW-20 s, S10–20 s, and MONET-3 s produced the highest T max , ΔT, and DC for both composites. The ΔT range among composites at different depths varied significantly (31.7–49.9 °C). DC of TPF ranged between 30–65% and in EVO between 15.3–56%. TPF had higher T max, ΔT for all depths and DC compared to EVO, across the LCU protocols (p < 0.05), except for PW-20 s and MONET-3 s. The coronal part of the restorations (1–2 mm) had the highest ΔT. There was a positive correlation between ΔT and DC at 4-mm depth after 120 s Significance Longer, or standard, exposure times of the LCUs delivered greater radiant exposures and had higher DC and ΔT compared to shorter or high-irradiance protocols. The fast photo-polymerised RBC had comparatively superior thermal and conversion outcomes when it received a high irradiance for a short time (1–5 s) compared to the conventional Bulk-Fill RBC.

‘Let there be Light,’ and there was Light, but was it Enough? A Review of Modern Dental Light Curing

Composite Cure and Pulp-Cell Cytotoxicity Associated with LED Curing Lights.

Light-curing dental resin-based composites: How it works and how you can make it work

The Photoinitiators Used in Resin Based Dental Composite—A Review and Future Perspectives

The dark art of light curing in dentistry

Effects of Light Attenuation through Dental Tissues on Cure Depth of Composite Resins

The Effects of Intensity, Exposure Time, and Distance of Polymerization Light on Vickers Microhardness and Temperature Rise of Conventional Resin-Based Composite

Effect of short LED lamp exposure on wear resistance, residual monomer and degree of conversion for Filtek Z250 and Tetric EvoCeram composites

Dual-cure dental composites: can light curing interfere with conversion?

Development in polymerization shrinkage control of dental light-cured resin composites: a literature review

High-Power LED Units Currently Available for Dental Resin-Based Materials—A Review

Effect of preheating and curing lamp distance on the degree of conversion of four nanohybrid resins: An in vitro study

Multi-peak Light-emitting Diode Curing Units and Polymerization of 3D-printed Crown and Bridge Resin

Moving Towards a Finer Way of Light-Cured Resin-Based Restorative Dental Materials: Recent Advances in Photoinitiating Systems Based on Iodonium Salts

Ability of Six Curing Lights to Photocure Four Resin-Based Composites in a MOD-Mold: A Double-Blind Study

The effect of light curing intensity on bulk-fill composite resins: heat generation and chemomechanical properties

Automotive Technology Revolutionized Restorative Dentistry Discovery of Alpha-diketone/Amine Catalyst: Part II -Reflections on Photopolymerization from Conception to Development of Composite Resin and Activator Light

What's Trending in Resin-Based Restorations

Thermography and conversion of fast-cure composite photocured with quad-wave and laser curing lights compared to a conventional curing light

Use of NIR light and upconversion phosphors in light-curable polymers

Factors that influence the clinical application of composite resins: Literature review