Abstract:Objectives This study investigated effects of the different emittance-mode protocols from three light curing units (LCUs): (i) a Laser (Monet); (ii) a quad-wave (PinkWave); (iii) a conventional LED (Elipar S10) on the temperature rise (ΔT) and degree of conversion (DC) when photo-curing fast or conventional bulk-fill resin-based composites (RBC). The aim was to correlate ΔT and DC, and the radiant exposure delivered to RBC specimens. Methods A 3D-printed resin mold of 4 mm depth was filled with two bulk-fill RBCs: Tetric PowerFill® ( fast photo-polymerised composite) ( TPF ) or Tetric EvoCeram® Bulk-Fill ( EVO ). Three LCUs were used: (i) Monet laser for 1 s and 3 s ( MONET-1 s, MONET-3 s ); (ii) PinkWave quad-wave used for 3 s in Boost mode ( PW-3 s ) and for 20 s in standard mode ( PW-20 s ); (iii) Elipar S10 for 5 s ( S10–5 s ) and for 20 s in standard mode ( S10–20 s ). 2-dimensional temperature maps were obtained before, during and for 60 s after the LCU had turned off using a thermal imaging camera. Thermal changes were analysed at five depths: (0, 1, 2, 3, and 4 mm from the top surface of the RBC). The maximum temperature rise ( T max ) and the mean temperature rise ( ΔT ) were determined. Cylindrical-shaped specimens were prepared from each material using a stainless-steel split mold (4 × 4 mm) and light-cured with the same protocols. The DC was measured for 120 s and at 1 h after LCU had turned off using Fourier Transform Infrared Spectroscopy (FTIR). Data were analysed using Three-way ANOVA, One-way ANOVA, independent t-tests, and Tukey post-hoc tests (p < 0.05). Results Radiant exposures delivered by the various irradiation protocols were between 4.5–30.3 J/cm 2 . Short exposure times from MONET-1 s and PW-3 s delivered the lowest radiant exposures (4.5 and 5.2 J/cm 2 , respectively) and produced the lowest ΔT and DC. The longer exposure times in the standard modes of PW-20 s, S10–20 s, and MONET-3 s produced the highest T max , ΔT, and DC for both composites. The ΔT range among composites at different depths varied significantly (31.7–49.9 °C). DC of TPF ranged between 30–65% and in EVO between 15.3–56%. TPF had higher T max, ΔT for all depths and DC compared to EVO, across the LCU protocols (p < 0.05), except for PW-20 s and MONET-3 s. The coronal part of the restorations (1–2 mm) had the highest ΔT. There was a positive correlation between ΔT and DC at 4-mm depth after 120 s Significance Longer, or standard, exposure times of the LCUs delivered greater radiant exposures and had higher DC and ΔT compared to shorter or high-irradiance protocols. The fast photo-polymerised RBC had comparatively superior thermal and conversion outcomes when it received a high irradiance for a short time (1–5 s) compared to the conventional Bulk-Fill RBC.

Multi-peak Light-emitting Diode Curing Units and Polymerization of 3D-printed Crown and Bridge Resin

Composite Cure and Pulp-Cell Cytotoxicity Associated with LED Curing Lights.

Post-curing of 3D printed resin using dental light curing unit

Effects of Post-Curing Light Intensity on the Mechanical Properties and Three-Dimensional Printing Accuracy of Interim Dental Material

Effect of Different Post-Curing Methods on the Degree of Conversion of 3D-Printed Resin for Models in Dentistry

Effects of post‐curing light intensity on the trueness, compressive strength, and resin polymerization characteristics of 3D‐printed 3‐unit fixed dental prostheses

Effect of short LED lamp exposure on wear resistance, residual monomer and degree of conversion for Filtek Z250 and Tetric EvoCeram composites

Influence of Battery Levels in Cordless LED Light-curing Units on Properties of Resin Cement and Glass Fiber Post Retention

Effects of different LED light curing units on the degree of conversion and microhardness of different composites: FT-IR and SEM-EDX analysis

Effect of Curing Modes on the Mechanical Properties of Commercial Dental Resin-Based Composites: Comparison between Different LEDs and Microwave Units

Thermography and conversion of fast-cure composite photocured with quad-wave and laser curing lights compared to a conventional curing light

Postpolymerization of a 3D-printed denture base polymer: Impact of post-curing methods on surface characteristics, flexural strength, and cytotoxicity

Ability of Six Curing Lights to Photocure Four Resin-Based Composites in a MOD-Mold: A Double-Blind Study

Impact of Battery Levels of a Cordless LED Curing Unit on Resin Cement under Varied Lithium Disilicate Thicknesses and Translucencies

Micro-Raman spectroscopic analysis of the degree of conversion of composite resins containing different initiators cured by polywave or monowave LED units

The Effect of Two Different Light-Curing Units and Curing Times on Bulk-Fill Restorative Materials

Influence of radiant exposure values from two third generation LED curing units on polymerization profile and microhardness of orthodontic composite under ceramic and metallic brackets

Effect of duration and infection control barriers of light curing unit on hardness of Bulk Fill composite resin

Effect of Post-Printing Conditions on the Mechanical and Optical Properties of 3D-Printed Dental Resin

Effects of UV Postcuring Times on the Color Stability, Surface Properties and Conversion of 3D-printed Temporary Resin Composites

Polymerization efficacy of composite resin cores with different fluidities under short-time super-intense light exposures