Thermography and conversion of fast-cure composite photocured with quad-wave and laser curing lights compared to a conventional curing light
Halah Thanoon,Richard B. Price,David C. Watts
DOI: https://doi.org/10.1016/j.dental.2024.01.003
2024-02-08
Dental Materials Journal
Abstract:Objectives This study investigated effects of the different emittance-mode protocols from three light curing units (LCUs): (i) a Laser (Monet); (ii) a quad-wave (PinkWave); (iii) a conventional LED (Elipar S10) on the temperature rise (ΔT) and degree of conversion (DC) when photo-curing fast or conventional bulk-fill resin-based composites (RBC). The aim was to correlate ΔT and DC, and the radiant exposure delivered to RBC specimens. Methods A 3D-printed resin mold of 4 mm depth was filled with two bulk-fill RBCs: Tetric PowerFill® ( fast photo-polymerised composite) ( TPF ) or Tetric EvoCeram® Bulk-Fill ( EVO ). Three LCUs were used: (i) Monet laser for 1 s and 3 s ( MONET-1 s, MONET-3 s ); (ii) PinkWave quad-wave used for 3 s in Boost mode ( PW-3 s ) and for 20 s in standard mode ( PW-20 s ); (iii) Elipar S10 for 5 s ( S10–5 s ) and for 20 s in standard mode ( S10–20 s ). 2-dimensional temperature maps were obtained before, during and for 60 s after the LCU had turned off using a thermal imaging camera. Thermal changes were analysed at five depths: (0, 1, 2, 3, and 4 mm from the top surface of the RBC). The maximum temperature rise ( T max ) and the mean temperature rise ( ΔT ) were determined. Cylindrical-shaped specimens were prepared from each material using a stainless-steel split mold (4 × 4 mm) and light-cured with the same protocols. The DC was measured for 120 s and at 1 h after LCU had turned off using Fourier Transform Infrared Spectroscopy (FTIR). Data were analysed using Three-way ANOVA, One-way ANOVA, independent t-tests, and Tukey post-hoc tests (p < 0.05). Results Radiant exposures delivered by the various irradiation protocols were between 4.5–30.3 J/cm 2 . Short exposure times from MONET-1 s and PW-3 s delivered the lowest radiant exposures (4.5 and 5.2 J/cm 2 , respectively) and produced the lowest ΔT and DC. The longer exposure times in the standard modes of PW-20 s, S10–20 s, and MONET-3 s produced the highest T max , ΔT, and DC for both composites. The ΔT range among composites at different depths varied significantly (31.7–49.9 °C). DC of TPF ranged between 30–65% and in EVO between 15.3–56%. TPF had higher T max, ΔT for all depths and DC compared to EVO, across the LCU protocols (p < 0.05), except for PW-20 s and MONET-3 s. The coronal part of the restorations (1–2 mm) had the highest ΔT. There was a positive correlation between ΔT and DC at 4-mm depth after 120 s Significance Longer, or standard, exposure times of the LCUs delivered greater radiant exposures and had higher DC and ΔT compared to shorter or high-irradiance protocols. The fast photo-polymerised RBC had comparatively superior thermal and conversion outcomes when it received a high irradiance for a short time (1–5 s) compared to the conventional Bulk-Fill RBC.
materials science, biomaterials,dentistry, oral surgery & medicine