Abstract:Grate furnaces are essentially equipped with the partitioned primary air and secondary air for regulating low-NO x combustion. However, habitual operations with primary air distributing uniformly on the grate and secondary air opened, present high NO x emissions and low burnout. While a comprehensive investigation into the in-furnace flow, coal combustion, and NO x formation (used to first explain and then improve these problems) is absent up to now. Accordingly, within a 75 t/h coal-fired reversal grate furnace, both full-scale tests and simulations were performed first at its habitual operation case. Subsequently, with secondary air completely shut off, four primary-air distribution forms of the uniform air (UA), front-lean air (FLA), middle-concentrated air (MCA), and rear-enhanced air (REA) were evaluated to compare the horizontal primary-air staging conditions. Flow-field deflection and asymmetric combustion occurred, with the upward gas deflecting toward the rear-wall side and the front-half furnace dominated by a weak recirculation zone without effective combustion. Using the UA but closing secondary air not only dropped effectively NO x but also improved a little burnout. This performance ruled against the vertical air-staging function of secondary air. In the order of UA, FLA, MCA, and REA to deepen the horizontal primary-air staging, the flow-field deflection and asymmetric combustion generally deteriorated a little. The in-furnace combustion first strengthened and then weakened. NO x emissions descended continuously. Among the four cases, the MCA attained the optimal low-NO x combustion performance (i.e. NO x emissions of 267 mg/m 3 at 6% O 2 and burnout loss of 6.14%, respectively). In comparison to the corresponding levels of 486 mg/m 3 and 5.4% at the habitual case, this simple MCA staging setup without any combustion modification, dropped NO x emissions by approximately 45% while raised only a little burnout loss.

CFD simulation and optimization of secondary air distribution for waste combustion in grate furnace

STUDY ON ELIMINATING FIRE-CARRYING IN PRIMARY AIR JET ORIFICE BY ADMIXING EXHAUST GAS

Numerical simulation of effects of flue gas recirculation on biomass combustion in grate boiler

Numerical Optimization Study of Combustion and Heat Transfer Characteristics in Municipal Solid Waste Incinerators

Optimization of the Air Distribution in a Biomass Grate-Fired Furnace

Optimization of Deposition Prevention Structure of a Grate Type Municipal Solid Waste Incinerator Based on CFD Numerical Simulation

Computational Fluid Dynamics Simulation of Combustion and Selective Non-Catalytic Reduction in a 750 T/d Waste Incinerator

Study on Drying and Combustion Process in Grate-Cfb Incinerator

Secondary air gates aided design of the two-stage reciprocating grate incinerator with CFD technology

Model for Waste Combustion in a Grate-Cfb

On the Furnace Design of Calculation of Circulating Fluidized Bed Boiler Fired Municipal Solid Waste

CFD Modelling and Optimization of Solid Waste Combustion in a 1 MW Fixed Bed Combustion Chamber

Numerical Simulation of Combustion and Characteristics of Fly Ash and Slag in a “V-type” Waste Incinerator

Influence of Multi-Temperature Primary Air on the Characteristics of MSW Combustion in a Moving Grate Incinerator

Numerical Simulation of the Impact of Secondary Air for a Pant-Leg 300 MW Circulation Fluidized Bed Boiler

The Co-Processing Combustion Characteristics of Municipal Sludge within an Industrial Cement Decomposition Furnace via Computational Fluid Dynamics

Advanced CFD modelling of air and recycled flue gas staging in a waste wood-fired grate boiler for higher combustion efficiency and greater environmental benefits

A two-fluid model simulation of an industrial moving grate waste incinerator

Numerical and experimental investigations on the performance of a 300 MW pulverized coal furnace

Partitioning Primary Air to Strengthen Efficiently the Horizontal Air-Staging Conditions within a 75 T/H Coal-Fired Reversal Grate Furnace

CFD simulation of MSW combustion and SNCR in a commercial incinerator