Abstract:Microstructure evolution,grain refinement mechanism and mechanical properties of face-centered cubic(fcc) metallic materials,subjected to equal channel angular pressing(ECAP),were systematically investigated.According to the special shear deformation mode of ECAP,Al single crystals with different orientations and Cu bicrystals with different initial grain boundary directions were subjected to ECAP for one pass,and it is found that shear deformations both parallel and perpendicular to intersection plane play important roles in the ECAP process.Moreover,Al single crystals,Cu single crystals and polycrystalline Cu-3%Si(mass fraction) alloy with different stacking fault energies (SFEs) and special crystallographic orientations,subjected to ECAP for one pass,were selected to experimentally and analytically explore the combined effects of crystallographic orientation,SFE and grain size on deformation twinning behaviors in several fcc crystals.Furthermore,ultrafine grained (UFG) or uanocrystalline(NC) Cu-Al alloys with different Al contents were prepared using multiple passes ECAP.The results show that the grain refinement mechanism is gradually transformed from dislocation subdivision to twin fragmentation,and the equilibrium grain size decreases with lowering the SFE of Cu-Al alloys.Meanwhile,the homogeneous microstructures of materials with high or low SFE are much more readily gained than those of medium-SFE metals.More significantly,the strength and uniform elongation can be simultaneously improved with lowering the SFE,i.e.,the better strength ductility combination is achieved in the Cu-Al alloy with lower SFE.

Effect of Equal Channel Angular Pressing on the Microstructure Evolution Andmechanical Property of the SiCP/AZ91 Composite Fabricated by Stir-Casting

Microstructure Evolution and Mechanical Properties of Nano-Sicp/Az91 Composite Processed by Extrusion and Equal Channel Angular Pressing (Ecap)

Enhancing mechanical properties and microstructure evolution of hybrid AZ61-5SiC-0.5CNTs composite during equal channel angular pressing

Effect of ECAP on the Microstructure and Tensile Property of SiCp/AZ91 Magnesium Matrix Composite

Equal-Channel Angular Pressing of Magnesium Alloy Az91 and Its Effects on Microstructure and Mechanical Properties

Equal channel angular pressing of a SiCw reinforced aluminum-based composite

The Effect of Equal Channel Angular Pressing on Coarsening Kinetics of AZ80–0.2Y–0.15Ca Alloy in Semisolid State

Microstructure and Mechanical Properties of Sicp/Az91 Composite Deformed Through A Combination of Forging and Extrusion Process

Processing and Mechanical Properties of Sic Particulate Reinforced Az91 Composites Fabricated by Stir Casting

Effect of equal channel angular pressing on microstructure and mechanical performance of innovative nano MgO-added Mg-Zn-Ca composite as a biomaterial

Microstructure and Mechanical Property of an Ecap Processed Al-Mg2si in Situ Composite by Using A Combined Route

Microstructure and mechanical properties of AZ61 alloys with large cross-sectional size fabricated by multi-pass ECAP

Microstructure Evolution and Mechanical Properties of Mg-Gd-Y-Zn-Zr Alloy During Equal Channel Angular Pressing

The Effect of Particles on Microstructure and Mechanical Behaviour of Mg-10Gd-3Y-0.4Zr Alloy Processed by ECAP

Effect of the Equal Channel Angular Pressing on the Microstructure and Phase Composition of a 7xxx Series Al-Zn-Mg-Zr Alloy

Microstructure and Mechanical Properties of Sicp/Mg-Zn-Ca Composites Fabricated by Stir Casting

Microstructure and Mechanical Properties of Ultrafine Grained Mg97Y2Zn1 Alloy Processed by Equal Channel Angular Pressing

Microstructure Evolution and Mechanical Properties of Fcc Metallic Materials Subjected to Equal Channel Angular Pressing

Microstructure and Elevated Tensile Properties of Submicron SiCp/AZ91 Magnesium Matrix Composite

Effect of Heat Treatment on Microstructure and Mechanical Properties of Squeeze Cast n SiCp/AZ91D Magnesium Matrix Composites

Evolutions of Microstructure and Mechanical Properties for Sicp/Az91 Composites with Different Particle Contents During Extrusion