Abstract:A Cu-0.41Mg-0.06Ca (wt.%) alloy was processed by equal channel angular pressing (ECAP) for up to 12 passes via Bc route at room temperature, and its homogeneity was evaluated from three aspects of hardness, microstructure and crystallographic texture. The hardness was measured in detail on the whole transverse planes, and the microstructure and the crystallographic texture in the central and bottom regions on the transverse planes were investigated by electron backscatter diffraction (EBSD) technique. After 1 ECAP pass, the hardness in the central region was 9.4% higher than that in the bottom region; the microstructure in the central region consisted of the elongated grains, while that in the bottom region was composed of the slightly distorted grains; the crystallographic texture in the central region followed the ideal orientations of the ECAP crystallographic texture, nevertheless the crystallographic texture in the bottom region obviously deviated from any ideal orientation of the ECAP crystallographic texture. Then, with the increase of ECAP passes, the hardness and microstructure differences between in the two regions gradually weakened, and the deviation of the crystallographic texture in the bottom region gradually decreased. After 8 ECAP passes, the both regions showed the same hardness, the similar ultrafine-grained microstructure and the similar crystallographic texture. The difference formation should be attributed to the non-uniform strain caused by the friction between the sample and the die wall, rather than caused by the corner gap. The difference weakening should be attributed to the strain hardening behavior of metals. The strength calculation showed that the Cu-Mg-Ca alloy after 8 ECAP passes had almost the same yield strengths where 593 MPa for the central region and 583 MPa for the bottom region, showing only 1.7% difference.

The Effect of Equal Channel Angular Pressing on Coarsening Kinetics of AZ80–0.2Y–0.15Ca Alloy in Semisolid State

Effect of the Equal Channel Angular Pressing on the Microstructure and Phase Composition of a 7xxx Series Al-Zn-Mg-Zr Alloy

Microstructure and Mechanical Properties of Mg–Zn–Ca Alloy Processed by Equal Channel Angular Pressing

Equal-Channel Angular Pressing of Magnesium Alloy Az91 and Its Effects on Microstructure and Mechanical Properties

Microstructure Evolution and Mechanical Properties of Mg-Gd-Y-Zn-Zr Alloy During Equal Channel Angular Pressing

Improvement of Strength and Ductility of Mg-Zn-Ca-Mn Alloy by Equal Channel Angular Pressing

The Effect of Particles on Microstructure and Mechanical Behaviour of Mg-10Gd-3Y-0.4Zr Alloy Processed by ECAP

Direct Observation of Shear Deformation During Equal Channel Angular Pressing of Pure Aluminum

Microstructure and Tensile Properties of A Mg-Zn-Y-Zr Alloy Containing Quasicrystal Phase Processed by Equal Channel Angular Pressing

Effect of Equal Channel Angular Pressing on the Microstructure Evolution Andmechanical Property of the SiCP/AZ91 Composite Fabricated by Stir-Casting

Effects of processing parameters on the microstructure of ECAE-formed AZ91D magnesium alloy in the semi-solid state

Compressive Deformation of Mg–Zn–Y–Zr Alloy Processed by Equal Channel Angular Pressing

Microstructure and Mechanical Properties of Ultrafine Grained Mg97Y2Zn1 Alloy Processed by Equal Channel Angular Pressing

Influence of ECAP Routes on Microstructure and Mechanical Properties of Mg–Zn–Ca Alloy

Microstructure Evolution and Mechanical Behavior of Mg-10Gd-3Y-0.4Zr Alloy Processed by ECAP at High Temperature

Superplasticity of Mg–Zn–Y Alloy Containing Quasicrystal Phase Processed by Equal Channel Angular Pressing

Equal Channel Angular Pressing Of Magnesium Alloy Containing Quasicrystal Phase

Lsothermal Grain Coarsening of Near-liquidus Casting and Equal Channel Angular Extrusion Formed ZK60 in the Semi-solid State

Effect of Equal Channel Angular Extrusion on the Thermal Conductivity of an AX52 Magnesium Alloy

Effect of ECAP on Mechanical and Damping Properties of Mg-0.6%Zr Alloy

Precipitation behaviors and mechanical properties of a solution-treated Mg-Gd-Nd-Zn-Zr alloy during equal-channel angular pressing process