Abstract:The microstructure evolution and crack propagation behavior were systematically and thoroughly investigated in & alpha;/ & beta; Ti-6Al-4V alloy obtained under the inhomogeneous heating effect of a coupled dual laser beam via a combination of postmortem electron backscattering diffraction analyses and numerical simulations. The effect of microstructural attributes (grain size, grain boundary, dislocation) on the fracture property and crack propagation behavior was investigated based on thermodynamic and crystallographic analyses, as well as the examinations of dislocation density and the Burgers vector. By quantifying the degree of variant selection using the degree of variant selection (DVS) equation, it was found that the higher the energy input, the weaker the variant selection, as the secondary & alpha; phase suppresses further dislocation-induced variant selection via autocatalytic nucleation and growth. The proportion of high angle grain boundaries (HAGBs) concentrated around 60 & DEG; gradually increases with improving cooling rate, mainly due to the change in the tendency of martensite transformation to be induced. The grain refinement was the primary mechanism for the enhancement of Ti-6Al-4V alloy T-joints, while the suppression of crack propagation by HAGBs also played a crucial role in improving strength and ductility. The crack propagation direction frequently changes when the order is approximately parallel to the short axis of & alpha;' martensite grains, forming a zigzag propagation path. The above findings should shed light on optimizing dual laser beam bilateral synchronous welding (DLBSW) technology to tailor the microstructure and improve the mechanical properties of Ti-6Al-4V alloy T-joints.& COPY; 2023 Published by Elsevier Ltd on behalf of The editorial office of Journal of Materials Science & Technology.

In-Situ SEM and EBSD Analysis on Plastic Behavior of Laser Beam Welding Ti-6Al-4V Alloy

In-Situ SEM and EBSD Analysis on Plastic Behavior of Laser Beam Welding Ti-6Al-4V Alloy [激光焊接Ti-6Al-4V钛合金塑性行为的原位SEM/EBSD分析]

In-situ Investigation of the Anisotropic Mechanical Properties of Laser Direct Metal Deposition Ti6Al4V Alloy

In-Situ Tensile Deformation Behavior Of As-Built Laser Direct Metal Deposited Ti-6al-4v Alloy At 200 Degrees C

Superplastic Tensile Behavior and Microstructure Evolution of Laser Welded Ti-6Al-4V Alloy

Micro-crystallographically revealing the plasticity-evolved behaviors of thick Ti–6Al–4V laser-arc hybrid welded joint

In Situ Investigation of the Tensile Deformation of Laser Welded Ti2alnb Joints

Microstructural and texture evolution investigation of laser melting deposited TA15 alloy at 500?C using in-situ EBSD tensile test

In-situ investigation into the deformation behavior of Ti-6Al-4V processed by laser powder bed fusion

In-situ Comparison of Deformation Behavior at 23 ℃ and 650 ℃ of Laser Direct Melting Deposited Ti-6Al-4V Alloy

In-situ EBSD-DIC Simulation of Microstructure Evolution of Aluminum Alloy Welds

Evolution of Plastic Deformation and Its Effect on Mechanical Properties of Laser Additive Repaired Ti64ELI Titanium Alloy

In-situ investigation on tensile deformation and fracture behaviors of inhomogeneous microstructure during laser repair of Ti-6Al-4 V titanium alloy

Investigation into Plastic Damage Behavior of the CO2 Laser Deep Penetration Welded Joint for Ti–6Al–4V Alloy

Microstructure Evolution and Fracture Behavior of 2060 AlLi Alloy by Laser Welding with TiC Nanoparticle-Reinforced Filling Wire

In-situ Investigation on Mechanical Behavior of Laser-Welded Joint for TC4 Titanium Alloy

Investigating the microstructural evolution during deformation of laser additive manufactured Ti–6Al–4V at 400 °C using in-situ EBSD

Microstructural Inhomogeneity in the Fusion Zone of Laser Welds

In Situ Observation of Deformation Behavior in a Ti600/Ti2AlNb Electron Beam Welded Joint

Temperature-gradient Induced Microstructure Evolution in Heat-Affected Zone of Electron Beam Welded Ti-6Al-4V Titanium Alloy

Bridging Microstructure and Crystallography with the Crack Propagation Behavior in Ti-6Al-4V Alloy Fabricated Via Dual Laser Beam Bilateral Synchronous Welding