Abstract:Ti–6Cr–5Mo–5V–4Al (Ti-6554) alloy has wide applications for large load-bearing components in the aerospace field. However, during the hot forming process of the alloy in the α+β phase region, there are a variety of interaction and restriction softening mechanisms and complex texture evolution behaviors, which jointly affect the microstructure and mechanical properties. This paper systematically studies the softening mechanism and texture evolution of Ti-6554 alloy in the α+β phase region using electron backscatter diffraction (EBSD), including dynamic phase transformation (DPT) and dynamic spheroidization of α phase and dynamic recrystallization (DRX) of β phase. Firstly, the effect of deformation parameters on the DPT is studied, and it is found that the volume fraction of α phase declines gradually with raising the strain rate, deformation temperature and deformation amount. The yield stress and the driving force for DPT increase with raising the strain rate and decreasing the deformation temperature. The equiaxed α phase will gradually transform into the lamellar α phase during the spheroidization process, accompanied by the wedging of the β phase. The combined effect of DPT and dynamic spheroidization leads to α grain refinement. Furthermore, the effect of deformation parameters on the DRX process of β phase is also investigated. The DRX degree only increases gradually with increasing the strain. Increasing the deformation temperature and decreasing the strain rate do not significantly increase the DRX volume fraction. Meantime, the DRX process of the β phase is heavily dependent on the α phase. The higher proportion of the α phase is capable of promoting continuous dynamic recrystallization (CDRX) process of β phase, while the lower proportion of the α phase will promote the transformation of CDRX into dynamic recrystallization (DDRX), but can not effectively increase the DRX degree of β phase. Further, the texture evolution shows that due to the combined effect of DPT and dynamic spheroidization, the effect of deformation parameters on the texture strength of α phase is very complicated. For the β phase, and fiber textures are easily formed during the deformation process.

Finite Element Simulation of Micro Stresses and Micro Strains in Two-Phase Titanium Alloy during Tension

In-situ Investigation Via High Energy X-ray Diffraction of Stress-Induced(0002)α→(110)β Transformation in a Ti-5.5Mo-7.2Al-4.5Zr-2.6Sn-2.1Cr Alloy

Phase Field Simulation of the Stress-Induced Α Microstructure in Ti–6Al–4 V Alloy and Its CPFEM Properties Evaluation

Research on microstructure of Ti-6Al-4V titanium alloy by thermal simulation under water cooling

In-Situ Study on Tensile Deformation and Fracture Mechanisms of Metastable β Titanium Alloy with Equiaxed Microstructure

A Numerical Simulation Method Considering Solid Phase Transformation and the Experimental Verification of Ti6Al4V Titanium Alloy Sheet Welding Processes

Small Punch Testing of a Ti6Al4V Titanium Alloy and Simulations under Different Stress Triaxialities

Phase Composition Effects on Dynamic Behavior and Strain Rate Sensitivity in Metastable β-Ti Alloys

In-situ investigation on the anisotropic behavior of the additively manufactured dual-phase Ti-6Al-4V alloy

Recent Advances on the Deformation Behavior of Two-Phase α+β Titanium Alloys

The role of β-titanium ligaments in the deformation of dual phase titanium alloys

Microstructure stability and damage mechanisms in an α/β Ti-6Al-4V-0.55Fe alloy during low cycle dwell-fatigue at room temperature

Research on hot deformation behavior and numerical simulation of microstructure evolution for Ti–6Al–4V alloy

Quantification of α phase strengthening in titanium alloys: Crystal plasticity model incorporating α/β heterointerfaces

TEM analysis of quasi in-situ formed tensile and fatigue cracks in a dual-phase Ti alloy

Study on the Relationship Between Microstructure and Mechanical Property in a Metastable Β Titanium Alloy

Constitutive Behavior of Titanium Alloy with Dual-Phase Microstructures: Experiments and Modeling

Identification of hardening and fracture behaviors of titanium alloy by a hybrid digital image correlation and finite element method

Systematic analysis of the softening mechanism and texture evolution of Ti–6Cr–5Mo–5V–4Al alloy during hot compression in α+β phase region

Ex-situ study on mechanical properties and deformation mechanism of three typical microstructures in TA19 titanium alloy

Deformation mechanisms in the α phase of the Ti-6Al-2Sn-4Zr-2Mo titanium alloy: in situ experiments and simulations