Abstract:The use of high strength low alloy steels provides several potential advantages including lower weight, lower manufacturing costs, and ease of handling and transport. The progress in steel manufacturing technology has continually called for new developments in welding processes and consumables to produce weld metal deposits with mechanical properties essentially equivalent to the base metal. Controlling the weld metal microstructures as well as raising the welding productivity is critical factor for the development of weld metal of high strength steel to secure satisfactory mechanical properties and to reduce production costs. In order to meet the demand to apply 1000 MPa class steel to the fabrication of large scale steel structures, a weld wire for the 1000 MPa class steel has been under development to obtain the required strength and toughness, which depend primarily on the microstructure. In this work, the effects of shielding gas composition on the microstructure and properties of 1000 MPa grade deposited metals produced by metal active gas (MAG) welding have been investigated. The shielding gas employed was a mixture of argon (Ar) and carbon dioxide (CO2) (5%similar to 30%), and the weld heat input was 13 kJ/cm. The properties of deposited metal with shielding gas of 80%Ar+20%CO2 is the best, the yield strength is 980 MPa, meanwhile, its Charpy absorbed energy at room temperature and -40 degrees C are 72.6 and 52 J, respectively. The results show that the microstructure of the deposited metal, consisting primary of low carbon martensite and a few parallel bainite plate, became more interweaved bainitic packets as the CO2 content of the shielding gas was increased. The initial bainite nucleated at austenite grain boundaries and subsequent bainite plates can form at the oxide inclusions of intragranular, which presented an intersected configuration and the microstructure was refined. The content of bainite palte and distribution morphology of martensite/bainite is the intrinsic reason attributed to mechanical properties of deposited metals. The content of bainite for deposited metal has an optimal proportion and more isn't necessarily better. It was also found that the area fraction, the size and the compositions of oxide inclusions in deposited metals were changed with increasing CO2 content. The deposited metal as using 70%Ar+30%CO2 has the minimum toughness because more large size oxide inclusions formed which are known to be harmful to the toughness.

PROCESS FOR IMPROVING THE QUALITY OF ER70S-6 STEEL FOR WELDING

Chemical composition optimization of ER70S-6 welding-wire steel

Design and evaluation of nitrogen-rich welding wires for high nitrogen stainless steel

Process optimization of aluminum/steel resistance spot welding based on dynamic resistance analysis

Quality Control of High Carbon Steel for Steel Wires

Prediction of Surface Wrinkle Defect of Welding Wire Steel ER70S-6 in Hot Bar Rolling Process Using Finite Element Method and Experiments

Optimization of shielding gas composition in high nitrogen stainless steel gas metal arc welding

The Effect of Process Parameters on Weld Quality in Resistance Spot Welding Dual-Phase Steels

Investigation of Process Stability and Weld Quality of Underwater Wet Flux-Cored Arc Welding of Low-Alloy High-Strength Steel with Oxy-Rutile Wire

Improving Weldability of Press Hardened Steel Through Combining Stepped Current Pulse and Magnetically Assisted Resistance Spot Welding Process

Study on the technology of controlling nitrogen content in molten steel

EFFECT OF SHIELDING GAS ON MICROSTRUCTURE AND PERFORMANCE OF 1000 MPa GRADE DEPOSITED METALS

Solidification cracking susceptibility and carbide evolution behavior in ERNiMo-2 weld metal: Effect and mechanism of Si content

Microstructural characteristics and tensile properties of ER70S-6 manufactured by Robotic CMT wire-and-arc additive manufacturing

Improvement of Weld Quality Using A Weaving Beam in Laser Welding

Quality Improvement in Resistance Spot Weld of Advanced High Strength Steel Using External Magnetic Field

The Effect of Martensitic Phase Transformation Dilation on Microstructure, Strain–Stress and Mechanical Properties for Welding of High-Strength Steel

Production Process Research and Quality Analysis of 77B Wire Rod

Steel Edge Cracking Analysis and Improvement Measures

Study on Improvement of Welding Technology and Toughening Mechanism of Zr on Weld Metal of Q960 Steel

Cause analysis of V-shaped crack pairs on drawn welding wire surface of ER70S-6 steel