Abstract:To further improve the mechanical properties and corrosion resistance of the biodegradable magnesium (Mg) alloy, the Mg-4Zn-0.5Sr-xAg alloy (x = 0.2 wt.%, 0.5 wt.%, 1.0 wt.%, and 2.0 wt.%) was smelted in vacuum under the protection of inert gas. The effect of the Ag content on the microstructure and mechanical properties of Mg-4Zn-0.5Sr was tested. The results show that the comprehensive properties of Mg-4Zn-0.5Sr-0.5Ag are best. The grain size of the Mg-4Zn-0.5Sr-0.5Ag alloy is minimal, that is, 83.28 μm. The average tensile strength (σb), yield strength (σs), elongation (ε), and hardness for the Mg-4Zn-0.5Sr-0.5Ag alloy is 168.00 MPa, 88.00 MPa, 12.20%, and 59.90 HV, respectively. To further improve the properties of cast Mg-4Zn-0.5Sr-0.5Ag alloy, extruding treatment was conducted. After extrusion deformation, the grain size of the alloy was significantly refined to 9 μm; at the same time, fine second phases were formed and evenly distributed in the matrix. And then, the mechanical properties of the alloy are significantly enhanced due to the effect of fine crystal strengthening and dispersion strengthening. The σb, σs, ε, and hardness value for the extruded Mg-4Zn-0.5Sr-0.5Ag alloy are 236.00 MPa, 212.00 MPa, 18.97%, and 65.42 HV, respectively. Under the synergistic action of adding the Ag element and extrusion treatment, the grain size of the alloy was significantly refined and the coarse second phase in the alloy became refined to disperse in the matrix, which benefits the formation of electric couples characterized as small cathode–large anode between the second phase and Mg matrix. During full immersion, corrosion products covered on the large anode surface could reduce the galvanic corrosion tendency.

Effect of homogenizing and extrusion on microstructure and corrosion resistance of Mg-Hg-Ga Alloy

Effect of Pre-homogenization Treatment on Microstructure, Mechanical Properties, and Corrosion Resistance of Hot Extruded AZ61 Magnesium Alloy

Effect of Microstructure on the Corrosion Behavior of as-cast and Extruded Mg–Sn–Y Alloys

Effect of Extrusion Process on Microstructure, Corrosion Properties, and Mechanical Properties of Micro-Alloyed Mg–Zn–Ca–Zr Alloy

Effect of Extrusion on Mechanical Property, Corrosion Behavior, and In Vitro Biocompatibility of the As-Cast Mg-Zn-Y-Sr Alloy

Effects of Deformation Microstructures on the Electrochemical Properties of Mg-Hg-Ga Alloy Anode

Synergistic Effects of Mg Alloying and Subsequent Homogenization Treatment to Improve the Microstructure and Properties of Al-Mg-Mn Alloys

Synergistic effects of alloying, homogenization, and hot extrusion on the mechanical properties of as-cast Mg–Al–Ca magnesium alloys

The Synergistic Effect of Trace Ag and Hot Extruding on the Microstructure and Properties of a Biodegradable Mg-Zn-Sr-Ag Alloy

The role of Ga in the microstructure, corrosion behavior and mechanical properties of as-extruded Mg–5Sn–xGa alloys

Effect of extrusion on the microstructure and corrosion behavior of Mg-Zn-Mn-(0, 1.5)Sr alloys in Hank’s solution

Improving the corrosion resistance of Mg-8Li-3Al-2Zn alloy by combining Gd alloying and hot extrusion

Evolution of Microstructure, Mechanical Properties, and Corrosion Resistance of Mg–2.2Gd–2.2Zn–0.2Ca (wt%) Alloy by Extrusion at Various Temperatures

Effect of extrusion process on microstructure and mechanical and corrosion properties of biodegradable Mg−5Zn−1.5Y magnesium alloy

Effects of Homogenization Treatment on the Microstructure and Mechanical Properties of Mg–8Li–3Al–Y Alloy

Modulation of corrosion properties by heat treatment and extrusion with mechanism analysis of high mechanical strength Mg-5.6Dy-3.1Ni alloy

Microstructure and mechanical properties of Mg-Gd-Zn-Zr alloy after hot extrusion

Hot Extrusion Effect on the Microstructure and Mechanical Properties of a Mg–Y–Nd–Zr Alloy

Investigation on corrosion behavior and mechanical properties of an extruded Mg-Zn-Al-Sn-Mn alloy

Effects of extrusion process on microstructure, precipitates and mechanical properties of Mg-Gd-Y-Zr-Ag alloys

Microstructure and corrosion behavior of as-homogenized and as-extruded Mg−xLi−3Al−2Zn−0.5Y alloys (x=4, 8, 12)