Abstract:The effects of different modeling and solving approaches on the simulation of a steam ejector have been investigated with the computational fluid dynamics (CFD) technique. The four most frequently used and recommended turbulence models (standard k-ε, RNG k-ε, realizable k-ε and SST k-ω), two near-wall treatments (standard wall function and enhanced wall treatment), two solvers (pressure- and density-based solvers) and two spatial discretization schemes ( the second-order upwind scheme and the quadratic upstream interpolation for convective kinematics (QUICK) of the convection term have been tested and compared for a supersonic steam ejector under the same conditions as experimental data. In total, more than 185 cases of 17 different modeling and solving approaches have been carried out in this work. The simulation results from the pressure-based solver (PBS) are slightly closer to the experimental data than those from the density-based solver (DBS) and are thus utilized in the subsequent simulations. When a high-density mesh with y+ < 1 is used, the SST k-ω model can obtain the best predictions of the maximum entrainment ratio (ER) and an adequate prediction of the critical back pressure (CBP), while the realizable k-ε model with the enhanced wall treatment can obtain the best prediction of the CBP and an adequate prediction of the ER. When the standard wall function is used with the three k-ε models, the realizable k-ε model can obtain the best predictions of the maximum ER, and the three k-ε models can gain the same CBP value. For a steam ejector with recirculation inside the diffuser, the realizable k-ε model or the enhanced wall treatment is recommended for adoption in the modeling approach. When the spatial discretization scheme of the convection term changes from a second-order upwind scheme to a QUICK scheme, the effect can be ignored for the maximum ER calculation, while only the CBP value from the standard k-ε model with the standard wall function is reduced by 2.13%. The calculation deviation of the ER between the two schemes increases with the back pressure at the unchoked flow region, especially when the standard k-ε model is adopted. The realizable k-ε model with the two wall treatments and the SST k-ω model is recommended, while the standard k-ε is more sensitive to the near-wall treatment and the spatial discretization scheme and is not recommended for an ejector simulation.

Optimal Design of Steam Ejector by Computational Fluid Dynamics Simulation

Numerical Investigation of Geometry Parameters for Design of High Performance Ejectors

Performance Improvement of Two-Phase Steam Ejector based on CFD Techniques, Response Surface Methodology and Genetic Algorithm

Numerical investigation on performance optimization of steam ejector considering full geometric parameters and working conditions

Optimal Design of Ejector Nozzle Profile with Internal and External Integrated Flow

Simulation Analysis of Ejector Optimization for High Mass Entrainment under the Influence of Multiple Structural Parameters

Numerical investigation of the effect of primary nozzle geometries on flow structure and ejector performance for optimal design

Analysis on the Optimal Mixing Pressure and Efficiency Limit of an Ideal Ejector

Assessment of Different CFD Modeling and Solving Approaches for a Supersonic Steam Ejector Simulation

Numerical optimization on the geometrical factors of natural gas ejectors

Optimization of exhaust ejector system for marine gas turbine enclosure cooling: Computational fluid dynamics analysis and parameter optimization

Theoretical Study on Predicting the Performance of Steam Ejector by Analogy Method

Performance computation and analysis of steam ejector

A CFD-based Investigation of the Two-Phase R744 Ejectors: Flow Pattern & Nozzle Design

Non-Condensation Turbulence Models with Different Near-Wall Treatments and Solvers Comparative Research for Three-Dimensional Steam Ejectors

Numerical Study on the Interaction of Geometric Parameters of a Transcritical CO2 Two-Phase Ejector Using Response Surface Methodology and Genetic Algorithm

A Parametric Study on the Effect of Mixing Chamber for Expansion Work Recovery CO2 Ejector

Numerical and Experimental Analysis of Two Phase Flow in Ejector

Experimental Investigation of an Improved Ejector with Optimal Flow Profile

Shape optimization and flow irreversibility mechanism analysis of normal temperature, high temperature and wet stream ejectors

Optimization of an ejector to mitigate cavitation phenomena with coupled CFD/BP neural network and particle swarm optimization algorithm