Abstract:The effects of different modeling and solving approaches on the simulation of a steam ejector have been investigated with the computational fluid dynamics (CFD) technique. The four most frequently used and recommended turbulence models (standard k-ε, RNG k-ε, realizable k-ε and SST k-ω), two near-wall treatments (standard wall function and enhanced wall treatment), two solvers (pressure- and density-based solvers) and two spatial discretization schemes ( the second-order upwind scheme and the quadratic upstream interpolation for convective kinematics (QUICK) of the convection term have been tested and compared for a supersonic steam ejector under the same conditions as experimental data. In total, more than 185 cases of 17 different modeling and solving approaches have been carried out in this work. The simulation results from the pressure-based solver (PBS) are slightly closer to the experimental data than those from the density-based solver (DBS) and are thus utilized in the subsequent simulations. When a high-density mesh with y+ < 1 is used, the SST k-ω model can obtain the best predictions of the maximum entrainment ratio (ER) and an adequate prediction of the critical back pressure (CBP), while the realizable k-ε model with the enhanced wall treatment can obtain the best prediction of the CBP and an adequate prediction of the ER. When the standard wall function is used with the three k-ε models, the realizable k-ε model can obtain the best predictions of the maximum ER, and the three k-ε models can gain the same CBP value. For a steam ejector with recirculation inside the diffuser, the realizable k-ε model or the enhanced wall treatment is recommended for adoption in the modeling approach. When the spatial discretization scheme of the convection term changes from a second-order upwind scheme to a QUICK scheme, the effect can be ignored for the maximum ER calculation, while only the CBP value from the standard k-ε model with the standard wall function is reduced by 2.13%. The calculation deviation of the ER between the two schemes increases with the back pressure at the unchoked flow region, especially when the standard k-ε model is adopted. The realizable k-ε model with the two wall treatments and the SST k-ω model is recommended, while the standard k-ε is more sensitive to the near-wall treatment and the spatial discretization scheme and is not recommended for an ejector simulation.

Optimization of an ejector to mitigate cavitation phenomena with coupled CFD/BP neural network and particle swarm optimization algorithm

Optimization of Dual-Impeller Configurations in a Gas–Liquid Stirred Tank Based on Computational Fluid Dynamics and Multiobjective Evolutionary Algorithm

The CFD Analysis of Cavitation Erosion and Structural Optimization for an Unloading Valve

Hydraulic Optimization of Super-low Specific Speed Multistage Flameproof Submersible Pump with Inner Motor for Coal Mine

Cavitation Suppression and Design Optimization in a Cryogenic Liquid Turbine Expander Based on Thermodynamic Cavitation and Entropy Production Analysis

Shape optimization and flow irreversibility mechanism analysis of normal temperature, high temperature and wet stream ejectors

Optimization of exhaust ejector system for marine gas turbine enclosure cooling: Computational fluid dynamics analysis and parameter optimization

Design Optimization Of A Mixed Flow Waterjet Pump For Performance Improvement Involving Cavitation

Energy Contribution Study of Blade Cavitation Control by Obstacles in A Waterjet Pump Based on Mpod and EEMD

Optimal Design of Steam Ejector by Computational Fluid Dynamics Simulation

Design Method of Water Jet Pump Towards High Cavitation Performances

Optimization of a Centrifugal Pump to Improve Hydraulic Efficiency and Reduce Hydro-Induced Vibration

Performance prediction and geometry optimization of ejector in PEMFC system using coupled CFD-BPNN and genetic algorithm

Multifactor response-based optimization for enhancing cavitation performance of short injection self-priming pumps

Simplified Ejector Model for Control and Optimization

Performance Improvement of Two-Phase Steam Ejector based on CFD Techniques, Response Surface Methodology and Genetic Algorithm

Numerical calculation and optimization designs in engine cooling water pump

Multi-objective Optimization of CO2 Ejector by Combined Significant Variables Recognition, ANN Surrogate Model and Multi-Objective Genetic Algorithm

Multi-Condition Optimization of Cavitation Performance on a Double-Suction Centrifugal Pump Based on ANN and NSGA-II

Assessment of Different CFD Modeling and Solving Approaches for a Supersonic Steam Ejector Simulation

Simulation Analysis of Ejector Optimization for High Mass Entrainment under the Influence of Multiple Structural Parameters