Abstract:The effects of different modeling and solving approaches on the simulation of a steam ejector have been investigated with the computational fluid dynamics (CFD) technique. The four most frequently used and recommended turbulence models (standard k-ε, RNG k-ε, realizable k-ε and SST k-ω), two near-wall treatments (standard wall function and enhanced wall treatment), two solvers (pressure- and density-based solvers) and two spatial discretization schemes ( the second-order upwind scheme and the quadratic upstream interpolation for convective kinematics (QUICK) of the convection term have been tested and compared for a supersonic steam ejector under the same conditions as experimental data. In total, more than 185 cases of 17 different modeling and solving approaches have been carried out in this work. The simulation results from the pressure-based solver (PBS) are slightly closer to the experimental data than those from the density-based solver (DBS) and are thus utilized in the subsequent simulations. When a high-density mesh with y+ < 1 is used, the SST k-ω model can obtain the best predictions of the maximum entrainment ratio (ER) and an adequate prediction of the critical back pressure (CBP), while the realizable k-ε model with the enhanced wall treatment can obtain the best prediction of the CBP and an adequate prediction of the ER. When the standard wall function is used with the three k-ε models, the realizable k-ε model can obtain the best predictions of the maximum ER, and the three k-ε models can gain the same CBP value. For a steam ejector with recirculation inside the diffuser, the realizable k-ε model or the enhanced wall treatment is recommended for adoption in the modeling approach. When the spatial discretization scheme of the convection term changes from a second-order upwind scheme to a QUICK scheme, the effect can be ignored for the maximum ER calculation, while only the CBP value from the standard k-ε model with the standard wall function is reduced by 2.13%. The calculation deviation of the ER between the two schemes increases with the back pressure at the unchoked flow region, especially when the standard k-ε model is adopted. The realizable k-ε model with the two wall treatments and the SST k-ω model is recommended, while the standard k-ε is more sensitive to the near-wall treatment and the spatial discretization scheme and is not recommended for an ejector simulation.

Impact of inlet steam state on ejector internal flow and performance considering non-equilibrium condensation

Effect of Vapour Condensation on Hot Steam Ejector System of Supersonic Wind Tunnel

Numerical investigation of spindle position effects on steam ejector performance with a nonequilibrium condensation model

Numerical Simulation on Two-Phase Ejector with Non-Condensable Gas

Numerical investigation in effects of refrigerants' thermodynamic properties on performance of supersonic ejector

Effect of droplets in the primary flow on ejector performance of MED-TVC systems

Experimental and numerical investigation of the effect of shock wave characteristics on the ejector performance

Performance Analysis of A Steam Ejector for A Steam Eject Refrigeration System

Assessment of Different CFD Modeling and Solving Approaches for a Supersonic Steam Ejector Simulation

Effect of Superheat Steam on Ejector in Distilled Water Preparation System for Medical Injection

Non-Condensation Turbulence Models with Different Near-Wall Treatments and Solvers Comparative Research for Three-Dimensional Steam Ejectors

The effect of the inlet steam superheat degree on the non-equilibrium condensation in steam turbine cascade

Numerical Investigation of a Two-Phase Ejector Operation Taking into Account Steam Condensation with the Presence of CO2

The Prediction of Condensation Characteristics of Supercritical Carbon Dioxide in the Laval Nozzle During Supersonic Flow

Analysis of the multiphase flow with condensation in the two-phase ejector condenser using CFD modeling

Numerical investigation on performance optimization of steam ejector considering full geometric parameters and working conditions

Energy efficiency and exergy destruction of supersonic steam ejector based on nonequilibrium condensation model

Transient numerical study of CO 2 two-phase flow in a needle adjustable ejector

Study on fundamental link between mixing efficiency and entrainment performance of a steam ejector

Performance of non-equilibrium condensation flow in wet steam zone of steam turbine based on modified model

Numerical Investigation on the Effect of Section Width on the Performance of Air Ejector with Rectangular Section