Abstract:The target in electron linear accelerator is subjected to high-frequency and intense thermal shocks. Elevated temperatures in the target may lead to target recrystallization, fatigue cracking, creep and vaporization. In this study, experiments were carried out to investigate the damage behaviour of tungsten targets in 6 MeV linear accelerators under pulsed electron beam. The results show that recrystallization occurs after loading 6 MeV electron beam with repetition frequency of 220 Hz, pulse width of 4 μs and mean current of 151 μA for 248 s. Deformation and cracking caused by recrystallization are observed on the surface of the target. INTRODUCTION Medical linear accelerators are the most commonly used device for external beam radiation treatments for patients with cancer [1]. The X-ray target is a very important component at the end of the accelerating tube to produce highenergy X-ray. Pulsed electron beam deposits large amounts of heat within the target. The target exposed to high-frequency thermal shocks is at risks of damage, limiting the accelerator’s ability to deliver high-dose-rate X-ray irradiation. Literature review shows several possible damage forms of the most commonly used tungsten targets [2-5]: (1) Recrystallization. Recrystallization temperature of pure tungsten is reported to be 1300-1500 °C. After recrystallization, the crystal structures of tungsten atoms change, causing the changes in the macro-properties. Micro-cracks initiate and propagate along grain boundaries. Besides, embrittlement happens with the ductile brittle transition temperature (DBTT) rising from 70 °C to 230-280 °C. (2) Fatigue cracking. Pulsed electron beam causes highfrequency thermal shocks on the target. Cyclic temperature variations lead to alternating stress and further mechanical fatigue of the target. As the temperature cycles cross the DDTT frequently, tungsten target shifts between flexible and brittle, easily initiating cracking and even failing. (3) Melting and vaporization. The melting point of tungsten is 3410 °C. Melting occurs when the energy deposited on the surface of tungsten exceeds its melting threshold with temperature lower than the melting point. Concomitant phenomenon including fondant motion, droplet sputtering and vapour layer formation will also damage the target. Research shows tungsten block initiates melting under heat load of 2 GW/m3 for 2 ms. Experiments need to be done to figure out the damage behaviour of tungsten target in accelerators to ensure stable operation of the accelerator and to get greater X-ray yield.

Basic Study on Destruction of Tantalum Target Bombarded by High Energy Flux Pulse Electron Beam

Restriction of Tantalum Target Expansion along Axis Bombarded by High-Current Pulsed Electron Beam

Measurement and simulation of the back-ejecta of tantalum target material impacted by high intensity current pulse electron beam

Experimental and Numerical Simulations of ELM-like Transient Damage Behaviors to Different Grade Tungsten and Tungsten Alloys

Analysis of Radiation Fields Induced by High Energy Electron Bombardment of Various Targets

Effects of Tantalum Alloying on Surface Morphology and Deuterium Retention in Tungsten Exposed to Deuterium Plasma

Molecular Dynamics Simulation of Atomic Beam Bombardment on a Solid Surface

DAMAGE BEHAVIOR OF TUNGSTEN TARGETS FOR 6 MEV LINEAR ACCELERATORS

Experimental Study of Destructive Effects on Materials with Different Energy Electron Bombardment

Numerical Study on Interaction of High Intense Pulsed Ion Beam and Ti Target

Study on the ablative characteristics of steel target irradiated by nanosecond pulsed pseudo spark electron beams: Experiment and molecular dynamics simulation

Temperature Field and Formation of Crater on the Surface Induced by High Curren T Pulsed Electron Beam Bombardment

Monte Carlo Study in Radiation Damage Experiments of Permanent Magnets by High Energy Electrons

Research on Numerical Simulation of Tantalum Explosively Formed Projectile Forming Driven by Detonation

Nanostructure Evolution and Surface Modification of Tungsten Exposed to Low Energy, High Flux Deuterium Plasma

Damages on Pure Tungsten Irradiated by Compression Plasma Flows

Model of Intense Pulsed Ion Beam and Simulation Study of Energy Deposited on Target

Molecular dynamics simulation of primary radiation damage in W-Ta alloys: Effect of tantalum

R&D of a MW-class Solid-Target for a Spallation Neutron Source

A Numerical Study of Cracks Appearance on Tungsten Surface after High Intense Pulsed Ion Beam Irradiation

Simulation on Surface Morphology Evolution of Metal Targets Irradiated by Intense Pulsed Electron Beam