Abstract:In the ultra-large-scale integration (ULSI) technologies, polysilicon resistors are usually employed in the integrated circuits as a precise analog resistor element for a variety of applications, such as DAC (digital resistor give the solution of the linearity and Rs concerns to analog converter) in analogue circuits [1-3]. Conventionally the polysilicon resistance can be adjusted by ion implantation and post annealing process [4]. For the self-aligned implantation process, the dosage changes which are always utilized to adjust the resistance are feasible to induce the MOS characteristics changes, especially in the submicron process whose short-channel effects (SCE) are much more sensitive to the dosages [5]. In this work, we propose a new inner anneal process in N2ambient after polysilicon re-oxidation to reduce the polysilicon resistance by changing the polysilicon grain size. The test patterns are manufactured on 300mm-diameter wafer by 65-nm 1-poly 7-metal standard CMOS technology. After polysilicon re-oxidation to form oxide film on polysilicon surface, the wafers are annealed at 800oC, 900oC, 950oC and 1000oC in N2ambient, respectively. Fig. 1 shows the process flow and annealing process steps in the flow. After anneal, the polysilicon grain size is measured by X-ray powder diffraction (XRD). And the electric characteristics for NMOS, PMOS and polysilicon resistance are tested. Fig. 2 shows the poly resistance reduction proportion and poly grain size after anneal at 800oC, 900oC, and 1000oC for 5min, and 950oC for 20min in N2 ambient, respectively. Only after annealing at 950oC or above for 5min, the resistance can be obviously reduced, due to the poly grain size increasing. Fig. 3 shows threshold voltages (Vt) variation proportions of NMOS and PMOS owning gate length of 65nm and width 0.12µm after utilizing annealing process at different temperatures. PMOS is more sensitive to the anneal process than NMOS. But after anneal at 950oC or below, the threshold variation for both NMOS and PMOS is less than 5%, which is acceptable for the integration process manufacturing. A new anneal process at N2 ambient to adjust the polysilicon resistance has been proposed. It has been verified that utilizing anneal process at 950oC or below, the 65nm MOS performances can be maintained almost same as before. Consequently, it is considered that the anneal method can be to be applied to the deep submicron integration process. References [1] C. D. Parikh, and R. M. Patrikar, Solid-state Electronics, 43, 683 (1999). [2] R. Murii, and M. J. Deen,, IEEE Trans. Electron Devices, 49, 187 (2002). [3] C. Uang, H. Chuang, S. Tsai, K. Thei, P. Lai, S. Fu, Y. Tsai, W. Liu, IWJT, 293 (2004). [4] S. Gupta, J. Electrochem. Soc. 149, G271 (2002). [5] R. H. Dennard, F. J. Gasensslen, H. M. Yu, V. L. Rideout, E. Bassous, A. R. Leblanc, Solid-state Circuits Soc Mag. IEEE, 87, 668 (1999). Figure 1

Double-Polysilicon Emitter RCA Devices and ICs at 77K

Improvement of RCA transistor using RTA annealing after the formation of interfacial oxide

Super High Speed Polysilicon Emitter Integrated Circuit Technology

Floating Low-Temperature Radio-Frequency Plasma Oxidation of Polycrystalline Silicon-Germanium

Very High Speed Poly-Si Emitter Bipolar Transistor and Circuit

High-speed Polysilicon Emitter Bipolar Technologies

High-Performance Polycrystalline Sige Thin-Film Transistors Using Al2o3 Gate Insulators

Very high speed polysilicon emitter bipolar transistor and circuit

RCA Microwave Power Bipolar Transistor with Excellent Performance

Research on Total Dose Effect of Double Polysilicon Self-Aligned NPN Transistors

Polysilicon Emitter Double Mesa Microwave Power SiGe HBT

Low-temperature and low thermal budget fabrication of polycrystalline silicon thin-film transistors

Performance and Reliability of Low-Temperature Polysilicon TFT With a Novel Stack Gate Dielectric and Stack Optimization Using PECVD Nitrous Oxide Plasma

A Simplified High-Speed Bipolar Process with Ti Salicide Metallization: Implementation of in Situ P-Doped Polysilicon Emitter

Influence of In-Situ Arsenic Doped Emitter Poly Process Conditions on RF-BiCMOS Device Parametrics

An equivalent heterojunction-like model for polysilicon emitter bipolar transistor

First Demonstration of Top-Gate Indium-Tin-Oxide RF Transistors with Record High Cut-off Frequency of 48 GHz, I<inf>d</inf> of 2.32 mA/μm and g<inf>m</inf> of 900 μS/μm on SiC Substrate with Superior Reliability at 85 °C

First Demonstration of Top-Gate Indium-Tin-Oxide RF Transistors with Record High Cut-off Frequency of 48 GHz, Id of 2.32 Ma/μm and Gm of 900 Μs/μm on SiC Substrate with Superior Reliability at 85 °C

Microstructure of the Emitter Polycrystalline Silicon/silicon Interface in Bipolar Transistors after Rapid Thermal Annealing

Thermal Method to Reduce the Polysilicon Resistance for Deep Submicron Integration Process

High Performance 70 Nm Cmos Device and Key Technologies