Abstract:High-textured pyrolytic carbon (PyC) is the ideal interface for SiC fiber-reinforced SiC matrix (SiCf/SiC) composites. To prepare high-textured PyC coatings on SiC fibers efficiently, chemical vapor deposition (CVD) technique was applied with the single precursor ethanol. The effects of CVD parameters on the morphology and textures of PyC were investigated in detail. Rough laminar (RL), smooth laminar (SL) and regenerative laminar (ReL) PyC could be obtained by controlling the CVD parameters. High-textured RL PyC could be stably synthesized in a large distance range in the horizontal tube furnace at 1150 °C and 10–20 kPa (total pressure), which inferred that low temperature and negative pressure were beneficial to the formation of RL PyC. Conversely, when the temperature was up to 1350 °C, the textures of PyC at different deposition positions varied considerably. In the vicinity of isothermal zone, the texture evolution of PyC with deposition positions followed the pattern of SL→RL→SL, which could be ascribed to the ratio change of the small linear hydrocarbons (fillers) and the aromatic hydrocarbons (particles) in the gas phase. The texture evolution followed the Particle-Filler model. In addition to PyC textures, the PyC coating thickness played a critical role in regulating the mechanical properties of SiC fibers and SiCf/SiC composites. In the present work, the effects of thickness of RL PyC coatings on the tensile properties of SiC fibers were investigated. The SiC fibers with 0.3 μm RL PyC coating showed the highest average tensile strength (2735 MPa) and Weilbull modulus (10.34), which might be ascribed to the repair of fiber surface defects and the appropriate stress state between fibers and coatings. The results could provide essential data for the interface design and optimization of SiCf/SiC composites.

EFFECT OF TENSION ON PYROLYSIS PROCESS OF POLYCARBOSILANE FIBER AND PROPERTIES OF SiC FIBER

Influence of SiC Coating Thickness on Mechanical Properties of SiCf/SiC Composite

Mechanical Behavior of SiCf/SiC Composites with Alternating PyC/SiC Multilayer Interphases

Properties of Carbon Nano-Tubes–cf/sic Composite by Precursor Infiltration and Pyrolysis Process

Effects of pyrochemical treatment for producing interfacial carbon layer on tensile properties of polymer-derived-matrix-based SiC/SiC composites

Texture control of pyrolytic carbon coatings and effects of coating thickness on the tensile properties of SiC fibers

Fabrication of Sic Fibres from Yttrium-Containing Polycarbosilane

Effect of polycarbosilane content on microstructures and mechanical properties of short-carbon-fibre-reinforced SiC composites

Effect of Impurities Control on the Crystallization and Densification of Polymer-Derived SiC Fibers

Synthesis of cyano-polycarbosilane and investigation of its pyrolysis process

Influence of polycarbosilane composition on the properties of SiC/SiC composite fabricated by precursor infiltration and pyrolysis process

Effect of Pyrocarbon Content in C/C Preforms on Microstructure and Mechanical Properties of the C/C–SiC Composites

Effect of pyrolytic carbon interphase on mechanical properties of mini T800-C/SiC composites

Synthesis of Polytitanocarbosilane and Preparation of Si–C–Ti–B Fibers

PyC interphase growth mechanism and control models of C/SiC composites

Fabrication of SiC ultrafine fiber with low oxygen content by electrospinning, thermal curing and pyrolysis of cyano-polycarbosilane

EFFECT OF PYROLYSIS TEMPERATURE ON MICROPORE SIZE DISTRIBUTION IN SILICON CARBIDE FIBERS BY THE SMALL ANGLE X-RAY SCATTERING

Effects of PyC coating on SiC fibers after ultra-high temperature annealing

Synthesis of Crystalline Sic Nanofiber Through the Pyrolysis of Polycarbomethylsilane Coated Platelet Carbon Nanofiber

Preparation of SiC ceramic fiber from a photosensitive polycarbosilane

Study on the Mechanical Property of High‐Performance Silicon Carbide Fiber