Abstract:Vinyl chloride/ N-phenylmaleimide copolymer ( VC/PMI) and vinyl chloride/ N-phenylmaleimide/ acrylonitrile terpolymer (VC/PMI/AN) were synthesized in the suspension copolymerization process for improving the heat resistance of poly( vinyl chloride) PVC) This paper emphasized on the studies on the characterization of the heat resistant properties of these three co) polymers mainly by means of dynamic mechanical experiment with the change of storage modulus ( E'), change rate of E' with temperature and mechanical loss factor ( tandelta) near the glass transition. The Vicat softening point ( VSP) was also tested supplementally for comparison. The lower the change rate of E' with temperature is, the higher the heat resistance of VC/PMI and VC/PMI/AN will be. The effects of the amount of PMI and AN in the recipes of copolymerization on the change rate of E' with temperature, tandelta and VSP were also investigated. The results show that the increase of the amount of PMI will increase the rigidity of the backbone of the copolymer chain so as to improve the heat resistance. On the other hand, the introduction of AN into the copolymer will give more uniform distribution of PMI unit or segment in the backbone, and thus improves the heat resistance of the copolymer further. It is discovered that there are two peaks of mechanical loss or two glass transition temperatures of VC/PMI/AN copolymerization product. It may be interpreted from the higher reactivities of PMI and AN than VC. During the copolymerization process of VC, PMI and AN, the more active PMI and AN will copolymerize more rapidly and will consume entirely at conversion of about 45% similar to 50%. Thereafter, VC continues to homopolymerize to form PVC homopolymer until a final conversion of 85%. Actually, the final product is a mixture of VC/PMI/AN terpolymer and homo-PVC, showing two T(g)s.

Preparation of PVC/MBS/EVA blends and its UV-irradiation resistance

Structure-property Relationships of Reactively Compatibilized PHB/EVA/starch Blends.

Study of Poly(vinyl Chloride)/acrylonitrile–styrene–acrylate Blends for Compatibility, Toughness, Thermal Stability and UV Irradiation Resistance

Compatibility of PVC/EVA Blends and the Pervaporation of Their Blend Membranes for Benzene/cyclohexane Mixtures

ULTRAVIOLET IRRADIATION MODIFICATION OF HDPE AND MECHANICAL PROPERTIES OF ITS BLEND WITH PVA

Thermal, Mechanical and Flame-Retardant Properties of Crosslinked Ethylene Vinyl-Acetate Copolymer /magnesium Hydroxide Blends by ~(60)co Irradiation

Phase Separation of Impact‐modified PVC/PMMA Blends under Melt‐blending Conditions

Reinforcing and Toughening Modification of poly (3-hydroxybutyrate-co-3-hydroxyvalerate)/ethylene-vinyl Acetate Copolymer (PHBV/EVA) Blends Compatibilized by Benzoyl Peroxide

Influence of Phase Separation on Mechanical and Anti-Uv Aging Properties of Polyvinylidene Fluoride/Polymethyl Methacrylate Blends

Heat Resistant Properties of Vinyl Chloride-N-Phenylmaleimide (-Acrylonitrile) Suspension Polymerized Copolymer

Effect of ultraviolet irradiation on strength and toughness of composites of poly(lactic acid) and poly(butylene adipate-co-terephthalate) with different mass ratio

Modification of ABS/PVC Blend

Preparation and characterization of a high molecular weight UV-stabilizer based on a derivative of 2,4-dihydroxybenzophenone and its application in polymer materials

Irradiation crosslinking and halogen-free flame retardation of EVA using hydrotalcite and red phosphorus

Effect of Environmental Temperature on Chemical Structure and Properties of Ultraviolet Irradiated Hdpe

Study on fracture of PVC/MBS blends

STUDIES ON FUNCTIONALIZATION OF HIGH DENSITY POLYETHYLENE AND ITS COMPATIBILIZATION EFFECT

Impact of γ-irradiation and SBR content in the compatibility of aminated (PVC/LLDPE)/ZnO for improving their AC conductivity and oil removal

Studies on Mechanical and Rheological Properties of Poly(Vinyl Chloride) Modified with Elastomers and Rigid Organic Particles

Effect of ultraviolet light irradiation intensity on chemical structure and compatibilization of HDPE to HDPE/PC blend

Effect of UV-induced crosslink network structure on the properties of polylactic acid/polybutylene adipate terephthalate blend