Abstract:New technologies in polymer synthesis and pipe extrusion equipment have led to the commercialization of high-performance, large-diameter, thick-wall high density polyethylene (HDPE) pipes. They have been used in the field of seawater transport and cooling to replace metal pipes, due to their advantages of high corrosion resistance and extensibility. Connection of HDPE pipe is important as it determines the safety of the entire piping system. Butt fusion welding is commonly used for HDPE pipe connection but may cause the formation of weak points in the welded joints, interfering the reliability of the pipeline system in the application of nuclear power plants. At present, there is a lack of research on evaluating the performance of welded joint for large-diameter thick-wall HDPE pipes made by butt fusion-welding. The purpose of this study is to investigate the influence of three different butt fusion-welding processes, i.e., single low pressure (SLP), single high pressure (SHP) and dual low pressure (DLP), by evaluating the performance of their welded joints, including characterizing tensile strength, extensibility, crystallinity and hardness. In specific, a thick-wall HDPE pipe with OD of 812.8mm and wall thickness of 74mm which is certified for nuclear safety class was used for study. Representative specimen from the outer, middle and inner part across the wall of the main pipe body and welded joints were taken for testing. Different test methods and specimens were designed to assess the feasibility of evaluating the welding performance from different welding process. The results showed that the mechanical properties of different locations of the welded joints were different, and the tensile strength and fracture energy of the middle part of the joint were lower than that of the inner and outer parts, which could be caused by the difference in the crystallinity and thickness of the melting zone influenced by welding processes, as can be seen from the analysis of DSC test and morphology observation. Hardness testing was conducted on the section of the welded joints, and it revealed that the micromechanical properties of the welded joints in the region of the heat-affected zone were enhanced significantly, which may be due to the annealing effect caused by welding process. In summary, The DLP process resulted in the best extensibility of the welded joints among three processes, suggesting that the joining pressure from welding process plays an important role in affecting the extensibility of the welded joints.

Study on Pressure Variation of PE-HD Pipes for Nuclear Power Plants in Hydrostatic Test

Experimental and Numerical Investigation on the Seismic Behavior of above Ground High Density Polyethylene Pipe in Nuclear Power Plant

Investigation On Creep-Rupture Failure Time Of Hdpe Pipe Under Hydrostatic Pressure

Hydrogen Environment Fatigue Test System Development of High Pressure Hydrogen Storage Vessels

Research on Hydrogen Environment Fatigue Test System and Correlative Fatigue Test of Hydrogen Storage Vessel

Prediction of Ductile Rupture Failure Life of HDPE Pipe

A Numerical Study on the High-Velocity Impact Behavior of Pressure Pipes

Effect of viscoelasticity on the hold pressure of plastic pipe reinforced by cross helically wound steel wires in leak test

Finite Element Analysis of High-Density Polyethylene Pipe in Pipe Gallery of Nuclear Power Plants

Safety Test Research of Pressure Pipes Containing Incomplete Welding Defects

Instability Analysis and Development of High Pressure Hydrogen Storage Vessels

Fatigue crack growth and slow crack growth of HDPE pipes under internal pressure and flat plate compression

Local buckling of deepwater oil-gas pipeline under high hydrostatic pressure

Design Fatigue Life Evaluation of High-Pressure Hydrogen Storage Vessels Based on Fracture Mechanics

Comparative study on the performance of butt fusion-welding processes for nuclear safety class large-diameter thick-walled PE pipes

Theoretical Assessment of Burst Failure of Internally Pressurized Defect-Free Pipelines with Plastic Anisotropy

Burst Pressure of Pipelines with Plastic Anisotropy under Combined Internal and External Pressures

Short-term burst pressure of polyethylene pipe reinforced by winding steel wires under various temperatures

Analysis on the Long-Term Hydrostatic Strength of Kevlar Fibre Reinforced Flexible Pipe

Comparison of Technical Standards Between Buried and above Ground Polyethylene Pipe in the Application of Nuclear Power Plant

Investigation On Acoustic Propagation Of Ultrasound In Polyethylene Pipe Used In Nuclear Power Plant