Abstract:Fused deposition modeling (FDM) 3D printing has the advantages of a simple molding principle, convenient operation, and low cost, making it suitable for the production and fabrication of complex structural parts. Moving forward to mass production using 3D printing, the major hurdle to overcome is the achievement of high dimensional stability and adequate mechanical properties. In particular, engineering plastics require precise dimensional accuracy. In this study, we overcame the issues of FDM 3D printing in terms of ternary material compounds for polyamides with gradient structures. Using multi-walled carbon nanotubes (MWCNTs) and boron nitride (BN) as fillers, polyamide 6 (PA6)-based 3D-printed parts with high dimensional stability were prepared using a single-nozzle, two-component composite fused deposition modeling (FDM) 3D printing technology to construct a gradient structure. The ternary composites were characterized via DSC and XRD to determine the optimal crystallinity. The warpage and shrinkage of the printed samples were measured to ensure the dimensional properties. The mechanical properties were analyzed to determine the influence of the gradient structures on the composites. The experimental results show that the warpage of pure polymer 3D-printed parts is as high as 72.64%, and the introduction of a gradient structure can reduce the warpage to 3.40% by offsetting the shrinkage internal stress between layers. In addition, the tensile strength of the gradient material reaches up to 42.91 MPa, and the increasing filler content improves the interlayer bonding of the composites, with the bending strength reaching up to 60.91 MPa and the interlayer shear strength reaching up to 10.23 MPa. Therefore, gradient structure design can be used to produce PA6 3D-printed composites with high dimensional stability without sacrificing the mechanical properties of PA6 composites.

Preparation of PA6/PP Gradient Materials and Their Properties

THE STUDY OF APPLIED BEHAVIOR OF PP/PA6 BY USING GRAFTED POLYPROPYLENE AS COMPATILIZER

A Flat Polymeric Gradient Material: Preparation, Structure and Property

Relationship between structure and properties in high-performance PA6/SEBS-g-MA/(PPO/PS) blends: The role of PPO and PS

Research on effect of ABS,MAH,DCP on property of PA6/ABS blend

Influence of Preparation Methods on the Structures and Properties for the Blends Between Polyamide 6co6t and Polyamide 6: Melt‐mixing and In‐situ Blending

Morphology, thermal behavior, and mechanical properties of nylon6/multi-monomer grafted polypropylene blends

THE STUDY ON PP/Talc FLAT POLYMEIC GRADIENT MATERIALS--(Ⅱ) PERFORMANCE

Chemical-resistant polyamide 6/polyketone composites with gradient encapsulation structure: An insight into the formation mechanism

Controls of Gradient Morphology and Surface Properties of Polymer Blends

Mechanical Properties of Gradient Copolymers of Styrene and N -Butyl Acrylate

Three-Dimensionally Printed Ternary Composites of Polyamide: Effect of Gradient Structure on Dimensional Stability and Mechanical Properties

Surface modification through gradient morphology control of polymer blends

Study on the Microstructures and Mechanical Behaviour of Compatibilized Polypropylene/Polyamide-6 Blends

Microstructures and Mechanical Properties of Polypropylene/polyamide 6/Polyethelene-Octene Elastomer Blends

Influence of Preparation Methods on Structure and Properties of PA6/PA66 Blends: A Comparison of Melt‐mixing and in Situ Blending

The Preparation of Monomer Casting Polyamide 6/Thermotropic Liquid Crystalline Polymer Composite Materials with Satisfactory Miscibility

Functionalization of Polypropylene and Compatibilization of Polypropylene/Nylon 6 Blends with Copolymers Containing Alpha-Methyl Styrene Units

Graft PP Compatibilizing Modification of PP/PA6 Alloy

Compatibilization Effect of PP-g-(MAH/VAc) on Polypropylene/Polyamide 6 Blends

Morphology and Mechanical Properties of Polyamide 6/Polystyrene Blends Prepared by Diffusion and Subsequent Polymerization of Styrene in Polyamide 6 Pellets