Abstract:The objective of the LuFo VI-1 project CATeW (Coupled Aerodynamic Technologies for Aircraft Wings) consists in multifidelity analyses to assess the potential for aerodynamic efficiency increase by combined application of hybrid laminar flow control and variable camber technologies to the wing of a transonic transport aircraft. Individually, both technologies have proven to lead to major aerodynamic drag reductions. An evaluation of the coupled technologies is, therefore, expected to show an even higher potential due to synergy effects. To derive conclusions on system level, low-fidelity (LowFi) overall aircraft design methodologies will be applied for the analysis of a medium haul reference aircraft in the course of the project, while complex aerodynamic phenomena are modelled with high-fidelity (HiFi) computational fluid dynamics methods. The paper at hand presents results of aerodynamic analyses on both fidelity levels for the wing of the turbulent reference configuration CATeW-01, featuring the technology combination as a retrofit. Furthermore, this work encompasses adaptations and implementations performed within both the LowFi and HiFi toolchains. The LowFi toolchain already incorporates several modules for the proposed technology combination. A short presentation of the LowFi-toolchain is given, along with the modeling approach in the HiFi framework using mesh deformations and a mass flux boundary condition. Comparative studies of the turbulent flow field around the wing show good agreement of predicted load distributions in both numerical frameworks, studies based upon the HiFi approach attest the potential for efficiency increase due to the variable camber technology, incorporated by means of Adaptive Dropped Hinge Flap (ADHF) deflections. Considering the coupled application, four different constant suction mass flow rates are examined, where the maximum mass flow causes laminar flow extending over the entire suction panel, thus moving the transition location from the wing's leading edge to the end of the suction panel. When being coupled with ADHF deflections, again the variable camber technology leads to a reduction of the wing's pressure drag component with the simultaneous application of boundary layer suction further promoting drag reduction with increasing suction rate. While the combined application shows no mutual inhibition, major reciprocal effects are not directly observable when applying the combination as a retrofit to the reference configuration CATeW-01. This is mainly attributed to the limited extend of laminar flow, thus indicating the necessity for optimization in wing geometry and operating parameters, to achieve extensive areas of laminar flow and to promote the aspired synergy effects.

Mechanical Simulation and Aerodynamic Analysis on a New Type of Wing Trailing Edge Variable Camber

Design and Validation of the Trailing Edge of a Variable Camber Wing Based on a Two-Dimensional Airfoil

Effects Of Cambers On Gliding And Hovering Performance Of Corrugated Dragonfly Airfoils

Numerical Study of a Supercritical Airfoil/wing with Variable-Camber Technology

Numerical analyses of a reference wing for combination of hybrid laminar flow control and variable camber

Comparative Analysis of Improved Aerodynamic Performance: Computational Fluid Dynamics Study of the Trailing Edge Morphing Concept Parameters

Methodology for Evaluating a Distributed Variable-Camber Trailing-Edge System in Preliminary Aircraft Design

Design and Experiment of a Seamless Morphing Trailing Edge

Analysis on the Aerodynamic Characteristics of Variable Camber Airfoils with Continuous Smooth Morphing Trailing Edge

A Study of Multi-Objective Aerodynamic Optimization Design for Variable Camber Airfoils and High Lift Devices

Numerical study on technical and conceptual improvements to a civil aircraft trailing-edge flap using passive/active flow control

Research on Adaptive Flexible Wing with Variable Trailing Edge

Ground Strength Test Technique of Variable-Camber Wing Leading Edge

Effects of thickness and camber on aerodynamic performance of flapping wings during forward flight

Mechanism Analysis of Hysteretic Aerodynamic Characteristics on Variable-Sweep Wings

Gust Load Alleviation Control Strategies for Large Civil Aircraft through Wing Camber Technology

Variable Camber Optimization Design of a Natural Laminar Airfoil

Fuel Efficiency Optimization of High-Aspect-ratio Aircraft Via Variable Camber Technology Considering Aeroelasticity

Aerodynamic Optimization of a High-Lift System with Adaptive Dropped Hinge Flap

Aerodynamic Optimization of an Adaptive Flap for Next-Generation Green Aircraft

The Design and Aerodynamic Analysis of Intelligent Variable Camber Airfoils with MFC