Abstract:The objective of the LuFo VI-1 project CATeW (Coupled Aerodynamic Technologies for Aircraft Wings) consists in multifidelity analyses to assess the potential for aerodynamic efficiency increase by combined application of hybrid laminar flow control and variable camber technologies to the wing of a transonic transport aircraft. Individually, both technologies have proven to lead to major aerodynamic drag reductions. An evaluation of the coupled technologies is, therefore, expected to show an even higher potential due to synergy effects. To derive conclusions on system level, low-fidelity (LowFi) overall aircraft design methodologies will be applied for the analysis of a medium haul reference aircraft in the course of the project, while complex aerodynamic phenomena are modelled with high-fidelity (HiFi) computational fluid dynamics methods. The paper at hand presents results of aerodynamic analyses on both fidelity levels for the wing of the turbulent reference configuration CATeW-01, featuring the technology combination as a retrofit. Furthermore, this work encompasses adaptations and implementations performed within both the LowFi and HiFi toolchains. The LowFi toolchain already incorporates several modules for the proposed technology combination. A short presentation of the LowFi-toolchain is given, along with the modeling approach in the HiFi framework using mesh deformations and a mass flux boundary condition. Comparative studies of the turbulent flow field around the wing show good agreement of predicted load distributions in both numerical frameworks, studies based upon the HiFi approach attest the potential for efficiency increase due to the variable camber technology, incorporated by means of Adaptive Dropped Hinge Flap (ADHF) deflections. Considering the coupled application, four different constant suction mass flow rates are examined, where the maximum mass flow causes laminar flow extending over the entire suction panel, thus moving the transition location from the wing's leading edge to the end of the suction panel. When being coupled with ADHF deflections, again the variable camber technology leads to a reduction of the wing's pressure drag component with the simultaneous application of boundary layer suction further promoting drag reduction with increasing suction rate. While the combined application shows no mutual inhibition, major reciprocal effects are not directly observable when applying the combination as a retrofit to the reference configuration CATeW-01. This is mainly attributed to the limited extend of laminar flow, thus indicating the necessity for optimization in wing geometry and operating parameters, to achieve extensive areas of laminar flow and to promote the aspired synergy effects.

Variable Camber Optimization Design of a Natural Laminar Airfoil

Effects of Cambers of Corrugated Airfoils on Gliding Performance by Using Lattice Boltzmann Method

Effects Of Cambers On Gliding And Hovering Performance Of Corrugated Dragonfly Airfoils

A Study of Multi-Objective Aerodynamic Optimization Design for Variable Camber Airfoils and High Lift Devices

Aerodynamic Optimization Design of Airfoil Configurations Based on Cascade Feedforward Neural Network

Unsteady Flow Simulation of a Variable-Sweep Morphing Aircraft Coupled with Flight Control System

Fuel Efficiency Optimization of High-Aspect-ratio Aircraft Via Variable Camber Technology Considering Aeroelasticity

Experimental and Numerical Studies on Aerodynamic Control of NACA 4418 Airfoil with a Rotating Cylinder

Sensitivity-Based Parameterization for Aerodynamic Shape Global Optimization

Numerical Study of a Supercritical Airfoil/wing with Variable-Camber Technology

Variable Camber Application to Aircraft in Formation Flight

Design and Validation of the Trailing Edge of a Variable Camber Wing Based on a Two-Dimensional Airfoil

Supercritical natural laminar flow airfoil optimization for regional aircraft wing design

Airfoil Optimization Using a Machine Learning-Based Optimization Algorithm

Numerical analyses of a reference wing for combination of hybrid laminar flow control and variable camber

Application of “objective Space Filtration” on Nacelle Cowl Design Variable Generation

Natural Laminar Flow Airfoil Design via Adjoint-Based Transition Onset Delay

AIRFOIL OPTIMIZATION WITH TRANSITION CURVE AS OBJECTIVE FUNCTION

Optimizing NACA Airfoil Thickness Function Parameters for Maximum Lift-to-Drag Ratio

Simulation Analysis and Experimental Study on Airfoil Optimization of Low-Velocity Turbine

Aerodynamic shape optimization using design-variables-screening method