Abstract:The laser cladding of the T15 high-speed steel (HSS) was accomplished and its typical microstructure was determined. The microstructure characterization of the clad layer showed three phases of microstructure, planar, cellular and equiaxed growth zones. Electron probe micro-analyzer (EPMA) showed high content in alloying elements at the cellular and equiaxed zones that contained V, C, Cr and W. Further, the analysis at the inter-granular zone presented the highest concentration in elements such as Mo, Cr and W. This showed the presence of carbides which were identified as MCI and M6C at the cellular zone, and M7C3 and M23C6 at the equiaxed and inter-granular zones. The precipitation characterization along the line starting from the substrate and passing through the clad layer identified the austenite matrix and revealed the fluctuation in the alloying elements content, where its amplitude and count increased while passing through the planar zone and hitting the equiaxed zone. Equilibrium phase diagram thermodynamic calculation proved the presence of MCI, M6C and M23C6 which precipitated respectively as the solidification proceeded. The M6C carbide was rich in Fe and W with the presence of V and Cr. MCI carbide had high content of C and V also with dissolved content of W and Cr. Finally, M23C6 carbide contained high amounts of W, Cr and Mo. Scheil–Gulliver simulation model showed the presence of M6C and MCI similar to the equilibrium phase diagram results, additionally, two carbides were revealed and identified as M7C3 and MCII carbides. The M23C6 was absent from the Scheil–Gulliver model. This is due to the assumption that in the Scheil–Gulliver model, the solid stage has no diffusion, and the M23C6 was proved to precipitate in later stages of solidification as shown in the equilibrium phase diagram results. Finally, transmission electron microscopy (TEM) and x-ray diffraction (XRD) showcased the presence of the carbides predicted from the equilibrium phase diagram.

Research Progress of Eutectic Carbides in High-Speed Steel

Development of Powder Metallurgy High Speed Steel

Effect of Alloying and Microalloying Elements on Carbides of High-Speed Steel: An Overview

Dissolution Behavior of Eutectic Carbides in Medium-Alloy Steels for Heavy Forgings

Rapid Solidification Microstructure and Carbide Precipitation Behavior in Electron Beam Melted High-Speed Steel

Study on Evolution Behavior of Carbides in Industrial‐Grade American Iron and Steel Institute M35 High‐Speed Steel Produced by Electroslag Remelting

Refinement of Eutectic Carbides in M2 High Speed Steel by Adjusting Magnetic Flux Density During Magnetic Controlled ESR Process

Carbide Precipitation Behavior of High‐Alloy Steel During Solidification and Cooling Process

Effect of Secondary Aerosol Cooling on the Characteristics of Carbides in M42 High‐Speed Steel Produced by the Electroslag Remelting Withdrawal Process

Effects of Carbides Distribution in Matrix on Thermal Fatigue and Wear Properties of High Speed Steel Rolls

Thermodynamic Calculation and Characterization of Carbide Precipitation in Laser-Deposited Material for High-Speed Steel Alloy

Effects of Niobium on Microstructure, Hardness and Wear Behavior for High-Speed Steel Rolls

Origin of Austenitization-Dependent Eutectoid Transformation in High-Speed Steel: Revisiting the Role of Primary Carbide

Mechanical and tribological assessments of high-vanadium high-speed steel by the conventional powder metallurgy process

Microstructural evolution and tribological properties of M2 high-speed steel fabricated under various selective electron beam melting processing parameters

Effect of titanium and rare earth microalloying on microsegregation, eutectic carbides of M2 high speed steel during ESR process

Research of a novel intermetallic compound-precipitation hardened steel bonded TiCN-based ceramic

Effect of Tempering Conditions on Secondary Hardening of Carbides and Retained Austenite in Spray-Formed M42 High-Speed Steel

Influence of Co on the microstructure and mechanical properties of M42 high-speed steel

Study on the rapid synthesis of high-entropy carbonitride powder and its remarkable hardening effects on cemented carbide tool materials

Carbides in High-Speed Steels Containing Silicon