Abstract:With a theoretical specific energy of 2500 W h kg-1 and energy density of 2800 W h L-1, the Li-S battery system is believed to provide the step-up in energy density necessary for lithium-based battery technologies to expand from portable electronics to transportation and grid-storage applications.1 However, the growth of dendrites during repeated Li plating/stripping and the low coulombic efficiency (CE) of these processes have limited application of rechargeable Li metal batteries.2 For example, a 300% excess amount of lithium often used in these batteries would directly result in halving the theoretical specific energy of the Li/S cells. In this presentation, the design of new electrolyte systems which enable high CE of lithium metal plating/stripping and high stability in the sulfur environment will be discussed. Tailoring of electrolyte properties for the lithium negative electrode has proven to be a successful strategy for improving the capacity retention and cycle life of Li-S full cells. This also enables lower electrolyte/sulfur mass ratios to be used and a lower excess of lithium metal; ultimately increasing the energy density of the system. A new class of electrolytes based on a high concentration of selected lithium salts in pure diethylene glycol dimethyl ether (diglyme) solvent provides a CE for lithium plating/stripping of greater than 99% for over 200 cycles and greater than 95% for over 500 cycles (Figure 1). In contrast, lithium metal cycles for less than 40 cycles at high CE in the standard 1 M LiTFSI + 2wt% LiNO3 in DOL:DME electrolyte. To realize the benefits of sulfur cathodes over intercalation cathodes currently using in Li-ion cells, high loading (high capacity) cathodes need to be used. In Figure 2a, a Cu||Li cell is cycled with the new diglyme-based electrolyte to a capacity of 6 mAh/cm2 at a current density of 0.6 mA/cm2 (C/10). Even at this high capacity, lithium is cycling with >99% CE. Lithium symmetrical cells were also cycled at a current density of 0.5 mA/cm2 to 5 mAh/cm2 (Figure 2b). In this case, the increase in polarization was used a metric to determine the practical cycle life of Li metal in the different electrolytes. No polarization is observed for the diglyme-based electrolyte after 2200 hours in the Li||Li cell. The inexpensive sulfur cathode paired with a low excess of lithium metal and the low-cost salt/solvent system may accelerate the applications of high energy density Li-S batteries in both electrical vehicles and large-scale grid energy storage markets. References 1. A. Manthiram, Y. Fu, S.-H. Chung, C. Zu, Y.-S. Su, Chem. Rev. 2014, 114, 11751-11787. 2. W. Li, H. Yao, K. Yan, G. Zheng, Z. Liang, Y.-M. Chiang, Y. Cui, Nature Comm. 2015, 6, 7436. Figure 1

A Mixed Ether Electrolyte for Lithium Metal Anode Protection in Working Lithium–Sulfur Batteries

A novel mixed ether-based electrolyte for lithium–sulfur batteries with Li anode protection by dual salts

Electrolyte Regulation Towards Stable Lithium‐Metal Anodes in Lithium–Sulfur Batteries with Sulfurized Polyacrylonitrile Cathodes

A Dynamically Stable Sulfide Electrolyte Architecture for High-Performance All-Solid-State Lithium Metal Batteries

Regulating Interface Dipole Interaction between Ethers and Active Species toward Highly Stable Li‐SPAN Batteries

Two birds with one stone: engineering siloxane-based electrolytes for high-performance lithium–sulfur polyacrylonitrile batteries

Tailored Electrolytes Enabling Practical Lithium–Sulfur Full Batteries Via Interfacial Protection

Lithium Polysulfide-Based Electrolytes for Li Metal Anodes

Strategy for High-Energy Li-S Battery Coupling with a Li Metal Anode and a Sulfurized Polyacrylonitrile Cathode

High-Performance Dual-Salt Electrolyte Based on Tetrahydrofuran and Dipropyl Ether for Lithium-Sulfur Battery

A new ether-based medium-concentrated electrolyte for lithium–sulfur battery with lean Li anode

Manipulating Electrolyte and Solid Electrolyte Interphase to Enable Safe and Efficient Li-S Batteries

Design of Novel Electrolytes to Protect Lithium Metal Anodes in Li-S Batteries

Protecting Li Metal Anode While Suppressing “Shuttle Effect” of Li-S Battery Through Localized High-Concentration Electrolyte

Stable Solvent-Derived Sulfur-Rich Inorganic Solid Electrolyte Interphase Via Solvation Modulation for Lithium Metal Batteries

Stabilizing Lithium Metal Anode Enabled by a Natural Polymer Layer for Lithium-Sulfur Batteries

A Diluted Electrolyte for Long-Life Sulfurized Polyacrylonitrile-Based Anode-Free Li-S Batteries

Li2S5-based Ternary-Salt Electrolyte for Robust Lithium Metal Anode

Lithium Metal Protection Enabled by In-Situ Olefin Polymerization for High-Performance Secondary Lithium Sulfur Batteries

Lithium-Anode Protection in Lithium–Sulfur Batteries

Lightweight Electrolyte Design for Li/Sulfurized Polyacrylonitrile (SPAN) Batteries