Abstract:A numerical modeling study, based on 3D finite element method (FEM) simulation and 1D analytical solutions, has been carried out to evaluate the capabilities of two ac methods for measuring in-plane thermal conductivity of thin film deposited on the back of a suspended SiNx membrane setup. Two parallel metal strips are present on the top of the dielectric membrane. One strip (S1) serves as both heater and thermometer, while another one (S2) acts as thermometer only. For a modified phase shift (MPS) method, it is crucial to extract the in-plane thermal diffusivity from the phase shift of the temperature oscillation on S2. It was found that the frequency window for carrying out the data fitting became narrower as the in-plane thermal diffusivity of the composite membrane (<math>α∥,C</math>) increased, primarily due to the failure of the semi-infinite width assumption in the low frequency region. To ensure the validity of the method, the upper limit of <math>α∥,C</math> should not exceed ~1.8 × 10−5 m2 s−1 for the specific membrane dimension under consideration (1 × 1 mm2). On the other hand, inspired by a modified Ångström method proposed by Zhu recently, we suggest a new data reduction methodology which takes advantage of the phase shift on both S1 and S2 as well as the amplitude on S1. Based on the simulation results, it is expected that the non-ideality associated with the three "observables" may be at least partially canceled out. Therefore, the frequency window selection for carrying out the data fitting is not sensitive to the magnitude of <math>α∥,C</math> and the upper limit of measurable <math>αC,∥</math> can be further increased with respect to the MPS method. For typical specimen films whose in-plane thermal conductivity ranges from 0.84 W m−1 K−1 to 50 W m−1 K−1, the method proposed here yields a theoretical measurement uncertainty of less than 5%.

Simultaneously Estimate Solid- and Liquid-Phase Thermal Conductivities

Thermal conductivity measurement of phase-change material near melting point based on perturbation method

Combined measurement and calibration method for the thermal conductivity of phase change materials

Sensitivity Analysis Of Thermophysical Properties On Pcm Selection Under Steady And Fluctuating Heat Sources: A Comparative Study

A volume-shrinkage-based method for quantifying the inward solidification heat transfer of a phase change material filled in spherical capsules

Phase equilibria -- thermal conductivity relationship within multicomponent Phase Change Materials from 273 K up to above the melting temperature

Transient Determination on the Bulk Thermal Conductivity of Sub-Millimeter Thin Films of Composite Phase Change Thermal Interfacial Materials

A simple method, the -history method, of determining the heat of fusion, specific heat and thermal conductivity of phase-change materials

Phase Change Material numerical simulation: enthalpy-porosity model validation against liquid fraction data from an X-ray computed tomography measurement/system

A Novel Method for Determining the Melting Point, Fusion Latent Heat, Specific Heat Capacity and Thermal Conductivity of Phase Change Materials

Numerical modeling of in-plane thermal conductivity measurement methods based on a suspended membrane setup

Metrology based on transient heat transfer theory for evaluating phase change materials with differential scanning calorimetry

An effective thermal conductivity model for the three-phase porous media based on the numerical simulation

Numerical Analysis of Effective Thermal Conductivity of Mixed Solid Materials

Experimental and numerical assessments of thermal transport in phase change material embedding additively manufactured triply periodic minimal surfaces: A comparative evaluation

Determination on the thermal conductivity and thermal contact resistance of thin composite phase change films as a thermal interfacial material

A new approach for the estimation of temperature-dependent thermal properties by solving transient inverse heat conduction problems

Simultaneous Reconstruction of Multiple Time-Varying Thermal Properties Based on Translucent Materials

Simultaneous Measurement of Thermal Conductivity and Heat Capacity Across Diverse Materials Using the Square-Pulsed Source (SPS) Technique

Comparison of Two CFD Approaches Using Constant and Temperature Dependent Heat Capacities during the Phase Transition in PCMs with Experimental and Analytical Results

Automatic Algorithm Applied for Calculating Thermal Conductivity by Transient Plane Source Method