Abstract:This paper presents the results of a numerical study on a supercritical CO2 (SCO2) turboshaft cooling device by considering heat transfer and hydrodynamics. A micro-cooling device with a radius clearance of 50 micron and a nozzle diameter of 4 mm was designed and used to investigate the heat transfer characteristics of a micro-spacing impinging and gas film dynamics. Sixteen nozzles ( N = 16) are equally spaced around the shaft in single or double rows. Investigations include journal speed- and eccentricity-dependent forward and cross-coupled force coefficients, and the effects of nozzle layouts and mass flow rate on the heat transfer efficiency. Analysis of the correlation coefficient shows that the gas density in the radial clearance is the dominant factor affecting the convective heat transfer performance, while the fluid velocity is a secondary factor. And the cooling efficiency (mass flow utilization rate) at low cooling pressure ( p s < 0.7 MPa) is significantly greater than that at high cooling pressure ( p s > 0.7 MP). In addition, considering the structure alone, a dual-row cooler exhibits a higher average Nusselt number, also registers a higher mass flow rate at the same pressure. Once the shaft is heated only one end, the difference in effectiveness between single- and dual-row cooling is not significant, so coolers with a single-row configuration should be preferred. Then, experimental values for the temperature of the heated rotor are provided under specific cooling airflow conditions. Dynamic analysis results show that the force coefficient of the single-row configuration is more dependent on the journal rotation speed and eccentricity ratio, and exhibits a negative direct stiffness coefficient at higher inlet pressure and journal rotation speed. Moreover, cross-coupled terms (stiffness coefficient) generally have a more explicit variation tendency than direct terms, and are more sensitive to changes in shaft speed and eccentricity. Small clearance cooling is a relatively complex technology aimed to improve heat dissipation efficiency in gas cooling devices while minimizing the effect of hydrodynamic pressure. Comparing the gas force coefficients of different journal speeds reveals a drastic increase in the effect of hydrodynamic pressure when the journal is eccentric. The cooler may be considered for operation with compliant support (such as bump foil) to generate additional damping and appropriately compensate for the eccentricity of the rotor.

Experimental Investigation into Rotating Loop Thermosyphons for Cooling Shafts of Motorized Spindles

Experimental Investigation of Single Loop Thermosyphons Utilized in Motorized Spindle Shaft Cooling

Experimental Investigation Of An R134a Loop Thermosiphon For Shaft Cooling

Investigation on Heat Transfer Performance of Loop Thermosyphon for Inner Cooling of Motorized Spindle

Thermal Performance of a R600a Two-Phase Loop Thermosiphon in Rotational Shaft

Visualization Research on a Pentane Loop Thermosyphon for Shaft Cooling

Evaluation of R404a single loop thermosyphon for shaft cooling in motorized spindle

Experimental Investigation of an R600a Two-Phase Loop Thermosiphon to Cool a Motorized Spindle Shaft

Experimental Investigation on the Start-Up Characteristics of Single Loop Thermosyphon for Motorized Spindle Bearing-Shaft System Cooling

Numerical study on two-phase flow and heat transfer characteristics of loop rotating heat pipe for cooling motorized spindle

Thermal Characteristics Analysis for a Motorized Spindle with Shaft Core Cooling Based on Numerical Simulation and Experimental Research

Development and evaluation of the thermal contribution of a vapor chamber cooling structure in the shaft for motor spindle

Experimental Study on an Thermosyphon Loop with Bubble Pump Effect

A Central Cooling Structure for Motorized Spindles: Principle and Application

An Investigation of the Temperature Distributions Inside A Spool Valve Owing to A Viscous Heating Effect

Thermal-structure Characteristics Coupling Analysis and Optimisation for Horizontal CNC Machining Centre Spindle

Study on Parameters of T-type Cooling System for Motorized Spindle Based on Thermal Characteristics

Thermal Management and Dynamic Performance of a Cooler Design for the Supercritical CO2 Turbine Shaft Cooling

Theoretical and Experimental Study on Rotating Heat Pipe Towards Thermal Error Control of Motorized Spindle

Design of cooling system and experimental research of grinding motorized spindle

Investigation on a Grinding Motorized Spindle with Miniature-Revolving-heat-pipes Central Cooling Structure