Abstract:In recent years, with the prohibition of CFC by international community, the cascade refrigeration cycle is showing the development of new features, in which Auto-cascade refrigeration cycle with its simple structure, reliable performance particularly has aroused widespread concern. This paper puts forward using the distillation column instead of the multi-stage segregation device, which make full use of the distillation column to provide good enough conditions for the vapour-liquid contact,creat a greater contact surface, ensure the space and time of heat and mass transfer between each component of refrigerant and lubricant, in order to achieve high efficient separation.This cycle uses environment-friendly non-azeotropic mixed (NARM) R600a\R23\R50 as refrigerant. The improved PT equation is used, according to the quality and energy conservation of the distillation column and heat exchanger to carry on thermodynamic analysis. On this basis, the selection and the calculation of the experimental apparatus and equipment carried out to self-made a auto-cascade refrigeration cycle prototype. Through the cooling test of the eight different mixture ratio, the best quality ratio is found and the minimum temperature the ratio can reach. Through repeated experiments, study that the cycle compression ratio of one component affect on the temperature inside the ultra-low temperature box, the cycle compression ratio of the different components under the same temperature inside the ultra-low temperature box affect on the system performance, and the three throttle, cold boxes cycle high and low pressure ratio and distillation column reflux liquid extraction rate affect on the system performance. The prototype broke the traditional method that access to the depth refrigeration needs multiple refrigeration compressors, only use a single-stage air-conditioning refrigeration compressor with lubrication, to achieve high and low boiling point component through the use of distillation devices, including high-performance lubricant separation, successfully reduced to below -80 degrees C, and system stability. According to the results of a series of experiments, analyzed the ratio of working fluid, cycle pressure ratio, distillation column extraction rate of liquid return, increase heat and the expenditure component's effect on the temperature in the ultra-low temperature box and the COP of system.

Evaluation of R404a single loop thermosyphon for shaft cooling in motorized spindle

Experimental Investigation of Single Loop Thermosyphons Utilized in Motorized Spindle Shaft Cooling

Experimental Investigation of an R600a Two-Phase Loop Thermosiphon to Cool a Motorized Spindle Shaft

A Comprehensive Study of Drop-in Alternative Mixtures for R134a in a Mobile Air-Conditioning System

Working Fluid Selection for a Small-Scale Organic Rankine Cycle Recovering Engine Waste Heat

Investigating the Thermal-Hydraulic Performance of New Refrigerant Mixtures Through Numerical Simulation of Minichannel and Microchannel Evaporators

A thermodynamic analysis of a transcritical cycle with refrigerant mixture R32/R290 for a small heat pump water heater

Thermoelectric-based cooling system for high-speed motorized spindle I: design and control mechanism

Thermal-structure Characteristics Coupling Analysis and Optimisation for Horizontal CNC Machining Centre Spindle

Experimental Investigations of the Influence Factors for the Boiling Heat Transfer Characteristics of R134a Coolant in a Loop Thermosiphon System

Analysis of Fluid-Thermal Coupling in Ferrofluid Bearing Used in High Speed Machines

Analysis of Cooling Structure of Axial Flux Permanent-Magnet Synchronous Motor for Electric Aircrafts

A Study On A New Auto-Cascade Refrigerating Cycle

Experimental study on the effect of filling ratio on an R141b two-phase thermosyphon loop with a horizontal parallel tube evaporator

Numerical investigations on the performance of a single-stage auto-cascade refrigerator operating with two vapor-liquid separators and environmentally benign binary refrigerants

Evaluation of Two-Phase Suction, Liquid Injection and Two-Phase Injection for Decreasing the Discharge Temperature of the R32 Scroll Compressor

Experimental research on boiling heat transfer mechanism of a pump-driven loop thermosiphon for R134a coolant

Experimental and Numerical Investigation on a CO2 Loop Thermosyphon for Free Cooling of Data Centers

Design and Thermal Characteristic Analysis of Motorized Spindle Cooling System

Comparison of Heat Transfer Characteristics of the Hollow-Shaft Oil Cooling System for High-Speed Permanent Magnet Synchronous Machines

An Experimental Investigation of an R744 Two-Phase Thermosyphon Loop Used to Cool a Data Center