Abstract:Cu3SbSe4, featuring its earth-abundant, cheap, nontoxic and environmentally friendly constituent elements, can be considered as a promising intermediate temperature thermoelectric (TE) material. Herein, a series of p-type Bi-doped Cu3Sb1−xBixSe4 (x = 0–0.04) samples were fabricated through melting and hot pressing process, and the effects of isovalent Bi-doping on their TE properties were comparatively investigated by experimental and computational methods. TEM analysis indicates that Bi-doped samples consist of Cu3SbSe4 and Cu2−xSe impurity phases, which is in good agreement with the results of XRD, SEM and XPS. For Bi-doped samples, the reduced electrical resistivity (ρ) caused by the optimized carrier concentrations and enhanced Seebeck coefficient derived from the densities of states near the Fermi level give rise to a high power factor of ~ 1000 µWm−1 K−2 at 673 K for the Cu3Sb0.985Bi0.015Se4 sample. Additionally, the multiscale defects of Cu3SbSe4-based materials involving point defects, nanoprecipitates, amorphous phases and grain boundaries can strongly scatter phonons to depress lattice thermal conductivity (κlat), resulting in a low κlat of ~ 0.53 Wm−1 K−1 and thermal conductivity (κtot) of ~ 0.62 Wm−1 K−1 at 673 K for the Cu3Sb0.98Bi0.02Se4 sample. As a consequence, a maximum ZT value ~ 0.95 at 673 K is obtained for the Cu3Sb0.985Bi0.015Se4 sample, which is ~ 1.9 times higher than that of pristine Cu3SbSe4. This work shows that isovalent heavy element doping is an effective strategy to optimize thermoelectric properties of copper-based chalcogenides.

Significantly enhanced thermoelectric figure of merit of n-type Mg3Sb2-based Zintl phase compounds via co-doped of Mg and Sb site

Electrical property enhancement and lattice thermal conductivity reduction of n-type Mg3Sb1.5Bi0.5-based Zintl compound by In&Se co-doping

Enhanced thermoelectric performance of n-type Mg3Bi2-based materials by Se doping and alloying engineering

Optimization of Thermoelectric Property of n‐Type Mg3Sb2 Near Room Temperature via Mn&Se Co‐Doping

Synergistic Effect of Band and Nanostructure Engineering on the Boosted Thermoelectric Performance of n‐Type Mg3+δ(Sb, Bi)2 Zintls

Na/Bi-co-doping and Heterogeneous Interfaces Leading to Enhanced Thermoelectric Performance of P-Type Mg3Sb2-based Zintls

Thermoelectric performance improvement of p-type Mg3Sb2-based materials by Zn and Ag co-doping

Enhancing Thermoelectric Performance of Mg3Sb2 Through Substitutional Doping: Sustainable Energy Solutions via First-Principles Calculations

Extraordinary thermoelectric performance, thermal stability and mechanical properties of n-type Mg3Sb1.5Bi0.5 through multi-dopants at interstitial site

Realizing Cd and Ag codoping in p-type Mg3Sb2 toward high thermoelectric performance

High thermoelectric performance at room temperature of n-type Mg3Bi2-based materials by Se doping

Enhancing the Thermoelectric Performance of n‐Type Mg3Sb2‐Based Materials via Ag Doping

Roles of concentration-dependent Cu doping behaviors on the thermoelectric properties of n-type Mg3Sb1.5Bi0.5

Excellent thermoelectric performance of boron-doped n-type Mg3Sb2-based materials via the manipulation of grain boundary scattering and control of Mg content

Effect of Sb Doping on the Thermoelectric Properties of Mg 2 Si 0.7 Sn 0.3 Solid Solutions

High-Performance Low-Cost n-Type Se-Doped Mg3Sb2-Based Zintl Compounds for Thermoelectric Application

Enhanced thermoelectric performance of Sb-doped Mg2Si0.4Sn0.6 via doping, alloying and nanoprecipitation

Realizing synergistic optimization of thermoelectric properties in n-type BiSbSe3 polycrystals via co-doping zirconium and halogen

Enhancing the effective mass and covalent bond strength of Cu 3 SbSe 4 -based thermoelectric materials by Mn/Sn co-doping

Effect of Sb-Doping on the Thermoelectric Properties of Mg2Si Based Compounds

Enhanced Thermoelectric Properties of Cu3SbSe4 Compounds by Isovalent Bismuth Doping