Abstract:Most spaceborne scientific experiment applications require a microgravity environment. The current high-precision accelerometers used for the spaceborne vibration isolation system generally have a noise floor of sub-μg/√Hz, which cannot meet the demand of higher-level microgravity measurements. This article introduces a micro-electromechanical system (MEMS) acceleration sensor that has a noise floor of 2–5 ng/√Hz and an input range of more than ±2 mg. Its three-component version, the MEMS microgravity measurement module (MEMS-M3), is designed to measure accelerations in the space microgravity environment and might be used in the active vibration isolation system for higher-level microgravity scientific experiments in the future. The MEMS-M3 has a volume of 105 × 90 × 115 mm3, a weight of 1.2 kg, and power consumption of 3 W. The performance of the MEMS-M3 has been characterized on the ground and a series of preflight reliability experiments have been conducted. Then, the MEMS-M3 installed inside the test spacecraft has been carried by the Long March 5B rocket (CZ-5B) to the low Earth orbit at 10:00 on May 5, 2020, and returned to Earth ground at 5:00 on May 8, 2020, both in UTC time. During the on-orbit period, the MEMS-M3 has been switched on for 11 h. After data processing, the transient, periodic, and steady accelerations can be observed by the MEMS-M3 and a much noisier shelf product IMU STIM300, verifying the functionality of the MEMS-M3. Apart from application in active vibration isolation systems for spaceborne scientific experiments, it can also be used for drag-free control of satellites and other space applications.This article has not yet been cited by other publications.

Micromachined Accelerometers with Sub-g/Hz Noise Floor: A Review

Micromachined Accelerometers with Sub-µg/√Hz Noise Floor: A Review

Micromachined Accelerometers with Sub-μg/√Hz Noise Floor: A Review

An In-Plane Low-Noise Accelerometer Fabricated with an Improved Process Flow

Noise Behaviors of a Closed-Loop Micro-Electromechanical System Capacitive Accelerometer

A Low-Power Digital Processing Circuit for Capacitive Accelerometer

Mechanical Design Optimization of A Single-Axis Moems Accelerometer Based on A Grating Interferometry Cavity for Ultrahigh Sensitivity

Optical Design and Analysis of a High Resolution MOEMS Accelerometer Based on Diffraction Grating

Design and Test of a Micromachined Resonant Accelerometer with High Scale Factor and Low Noise

Sub-micro-g Resolution Test of Accelerometers Based on Tilt Dynamic Modulation in Gravity Field

A Sensitive Micromachined Resonant Accelerometer for Moving-Base Gravimetry

Noise Analysis and In Situ Detection of the Electromagnetic Servo Actuator for a Nano-g Accelerometer With a Large Dynamic Range

A Sub-µg Bias-Instability MEMS Oscillating Accelerometer with an Ultra-Low-Noise Read-Out Circuit in CMOS

MEMS Microgravity Measurement Module with Nano-g/Hz Noise Floor for Spaceborne Higher-Level Microgravity Scientific Experiment Applications

An aerosol deposition based MEMS piezoelectric accelerometer for low noise measurement

In-Depth Analysis of Low-Cost Micro Electromechanical System (MEMS) Accelerometers in the Context of Low Frequencies and Vibration Amplitudes

A High-Performance MEMS Accelerometer with an Improved TGV Process of Low Cost

Noise Analysis and Performance Improvement of a MEMS Fabry-Pérot Seismic Accelerometer

An optimized micromachined convective accelerometer with no proof mass

Compact optomechanical accelerometers for use in gravitational wave detectors

Low-Noise Drive of a Micromachined Resonant Accelerometer with Separated Sensing and Actuation