Abstract:Lead zirconate titanate (PZT)-based ferroelectric ceramic materials are piezoelectric materials of commercial importance. Strontium zirconate titanate (SZT) perovskite materials also have a wide application area. PZ and SZT starting solutions can be prepared using a variety of suitable methods. Among these methods, the sol-gel process has attracted special attention due to the low temperature requirement, homogeneity and the ability to obtain the appropriate particle size. The electrospinning method is the most effective and widely used method in nanofiber production. Electro-spinning is a method that enables the production of solid and hollow nanofibers in long lengths, homogeneous diameters and various compositions. When the electro-spinning technology is combined with the sol-gel method, continuous nanofibers, nanotubes and filled nanofibers are produced from polymer or ceramic solution under a certain electric field. In this study, lead zirconate titanate (PZT) and strontium zirconate titanate (SZT) solutions containing Sr and Pb were prepared by sol-gel method. Solutions were prepared using metal salts and alkoxides as the precursor materials. The solutions obtained were fed at flow rates of 1.6, 1.8, 2.0 mL / hour and PZT and SZT nanofibers were formed by electrospinning method at 20 kV voltage rating. Different parameters of the electrospinning device were examined and the SZT and PZT nanofibers were produced with optimum properties. Crystal structure, characterization of morphological surface and chemical properties of the produced nanofibers were done with XRD, SEM and EDX, respectively. XRD results showed that the perovskite structure of PZT and SZT was not damaged during Sol-gel and electrospinning processes. A small amount of beady structure was observed in SEM analysis of PZT and SZT nanofibers. According to EDX analysis of nanofibers, it was observed that the PZT and SZT structure was also formed.

Fabrication of Nanofibres Via Polyvinylpyrrolidone by Sol-Gel Method and Electro-Spinning Technique

Electrospun zirconia nanofibers and corresponding formation mechanism study

Fabrication of dense and porous Li2ZrO3 nanofibers with electrospinning method

Preparation of Zinc Oxide Nanofibers by Electrospinning

Fabrication and Characterization of Size-Controlled Single-Crystal-like PZT Nanofibers by Sol–gel Based Electrospinning

Preparation and Characterization of PbO.ZrO2.TiO2 and SrO.ZrO2.TiO2 Nanofibers by Electrospinning Method

Synthesis of Hollow PVP/Ag Nanoparticle Composite Fibers via Electrospinning under a Dense CO2 Environment

Exploration of single-crystal like electrospun Pb(Zr_(0.52)Ti_(0.48))O_3 nanofibers synthesis via electrospinning

PVA Nanofibers Embedded with Different Concentration of ZnO Prepared by Electrospinning Method

Preparation of YIG Single Crystal Nanofibers Via an Electrospinning Technique

Fabrication and characterization of zein-based nanofibrous scaffolds by an electrospinning method.

Preparation of ZnO Nanofibers with High Specific Surface Area

Preparation and Properties of Poly (vinyl Alcohol) Nanofibers by Electrospinning

Fabrication and Piezoresponse of Electrospun Ultra-Fine Pb(Zr0.3, Ti0.7)O3 Nanofibers

Fabrication of nanofiber yarns via electro-blown and hang-fiber process

LaMnO3 and La0.875Sr0.125MnO3 Nanofibers via Electrospinning

Effect of Temperature on Optimization of ZrO2 Nanofiber Produced by Electrospinning Method

Preparation, characterization, and the antimicrobial activity of PVA-PVP/ZnO nanofiber films via indigenous electrospinning setup

Optimization design and properties of PVA/GEL nanofibers

Fabrication and Sensing Behavior of Cr2o3 Nanofibers Via in Situ Gelation and Electrospinning

Electrospun fibers of poly (vinyl alcohol): zinc acetate (PVA:AcZn) and further ZnO production: evaluation of PVA:AcZn ratio and annealing temperature effects on ZnO structure