Abstract:Lead zirconate titanate (PZT)-based ferroelectric ceramic materials are piezoelectric materials of commercial importance. Strontium zirconate titanate (SZT) perovskite materials also have a wide application area. PZ and SZT starting solutions can be prepared using a variety of suitable methods. Among these methods, the sol-gel process has attracted special attention due to the low temperature requirement, homogeneity and the ability to obtain the appropriate particle size. The electrospinning method is the most effective and widely used method in nanofiber production. Electro-spinning is a method that enables the production of solid and hollow nanofibers in long lengths, homogeneous diameters and various compositions. When the electro-spinning technology is combined with the sol-gel method, continuous nanofibers, nanotubes and filled nanofibers are produced from polymer or ceramic solution under a certain electric field. In this study, lead zirconate titanate (PZT) and strontium zirconate titanate (SZT) solutions containing Sr and Pb were prepared by sol-gel method. Solutions were prepared using metal salts and alkoxides as the precursor materials. The solutions obtained were fed at flow rates of 1.6, 1.8, 2.0 mL / hour and PZT and SZT nanofibers were formed by electrospinning method at 20 kV voltage rating. Different parameters of the electrospinning device were examined and the SZT and PZT nanofibers were produced with optimum properties. Crystal structure, characterization of morphological surface and chemical properties of the produced nanofibers were done with XRD, SEM and EDX, respectively. XRD results showed that the perovskite structure of PZT and SZT was not damaged during Sol-gel and electrospinning processes. A small amount of beady structure was observed in SEM analysis of PZT and SZT nanofibers. According to EDX analysis of nanofibers, it was observed that the PZT and SZT structure was also formed.

Effect of Temperature on Optimization of ZrO2 Nanofiber Produced by Electrospinning Method

Effect of Heating Rate on Morphology and Structure of Cofe2o4 Nanofibers

Growth of Nanofibers Zinc Oxide on Porous Silicon Substrates using Electrospinning Method: Effect of Temperatures

Preparation and Characterization of Sc2o3-Doped Zro2 Nanofiber

Electrospun zirconia nanofibers and corresponding formation mechanism study

Oriented Nanofibers by a Newly Modified Electrospinning Method

Preparation and Characterization of PbO.ZrO2.TiO2 and SrO.ZrO2.TiO2 Nanofibers by Electrospinning Method

Effects of electrostatic polarities on the morphology of electrospun oxide nanofibers: A case study on alumina-based nanofibers

Preparation of Zinc Oxide Nanofibers by Electrospinning

Electrospinning of Ultra-Thin Nanofibers Achieved Through Comprehensive Statistical Study

Preparation of YIG Single Crystal Nanofibers Via an Electrospinning Technique

Specific role of Al in the synthesis of electrospun Al:ZnO nanofibers: Thermal and elemental analysis

Effects of Temperature on Melt Electrospinning: Experiment and Simulation Study

Growth mechanism and phase transformation of ZrO2 nanofibers fabricated by sol–gel electrospinning

Understanding the Interplay of solution and process parameters on the physico-chemical properties of ZnO nanofibers synthesized by sol-gel electrospinning

An Investigation into Scalability Production of Ultra-Fine Nanofiber Using Electrospinning Systems

Preparation of Magnesium Aluminate Spinel Nanofibers with High Temperature Resistance by Electrospinning Process Based on Non-Hydrolytic Sol-Gel Method

Effect of polymer concentration and annealing temperature on TiO2-PVP composite nanofiber mats prepared with homemade electrospinning

Preparation of Li6Zr2O7 Nanofibers with High Li‐Ion Conductivity by Electrospinning

Electrospun fibers of poly (vinyl alcohol): zinc acetate (PVA:AcZn) and further ZnO production: evaluation of PVA:AcZn ratio and annealing temperature effects on ZnO structure

Electrospun LaAlO3 nanofibers from different solvent systems